×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerIn this proposed study, all environmental factors affecting the aboveground and buried pipes, such as solar radiation and temperature, and soil temperature, have been studied on the characteristics of flow inside the aboveground and underground pipelines by building a mathematical model using MATLAB based on energy balance equations. From the mathematical model, the effect of solar radiation on the aboveground section of the pipeline is significate. During March and an inlet temperature of 34 °C, the pipeline outlet fluid temperature will rise to 50 °C. Other parameters affecting the aboveground section of the pipeline, such as ambient temperature and wind speed, have a much smaller effect on the fluid temperature, and the temperature difference is approximately 4 °C between the highest and lowest pipeline outlet fluid temperature. The result for the underground section of the pipeline showed that the main affecting parameter on the fluid temperature is the burry depth of the pipeline, the deeper the pipeline depth the lower the temperature variation and the lower fluid temperature can be seen, at 1 meter of bury depth the minimum and maximum fluid temperature was 18 °C and 36 °C respectively, and at 5 meters of bury depth, the minimum and maximum fluid temperature was 26 °C and 31 °C respectively. This study also checks different process parameters. Some of these are fluid flow, pipe diameter, and pipe material. The effect of the fluid flow and pipe diameter has a similar impact on the fluid temperature (while fixing all the other parameters), the higher the fluid flow or the smaller the pipe diameter resulted in a better heat transfer and more considerable temperature difference, and vice versa. The final process parameter, pipe material, had little to no effect on the fluid temperature variation.
Modern life makes energy, and the source of it is very important. This renewable energy comes from the Earth-Air Heat Exchanger (EAHE) in the soil employed as an air conditioning device for buildings in the climate conditions in Basrah city, south of Iraq. In the present study, the EAHE buried in the soil is simulated numerically using the finite volume method with a soft package. ANSYS: Fluent 2021/R2. A parametric analysis was carried out to determine the effect of three depths ( Z = 1, 2, and 3 m), taking into account the physical properties of the soil in the area under study, which is in the city of Basrah in southern Iraq, at longitude 47.749° and latitude 30.568°, as well as the data and time of 1/6/2023 at 12 p.m., the diameter of the pipe ( D = 7.62, 10.16, and 15.24 cm), and different velocities ( v = 0.5, 1, and 1.5 m/s). The results are presented as a temperature contour and a velocity contour for the performance of EAHE. The important results showed that when the depth of the buried pipe decreases, the temperature of the air outlet and heat exchanger increases; when the diameter decreases, the air outlet temperature from the EAHE and the soil temperature decrease; when the length of the pipe is about 30 m, after this length, the decrease in temperature is very small; and the maximum temperature difference of about 10 °C between the ambient temperature and the outlet temperature of the EAHE was obtained at a depth of 3 m and a velocity of 1 m/s at a diameter of 7.62 cm.
In this study a two dimensional, steady state propagation of the laminar premixed flame was numerically and experimental are investigated. The energy, momentum, continuity equations for species and global reaction mechanism with equation of stat for ideal gases were solved. Constant temperature boundary condition is applied on axi – symmetric in y – direction domain. The governing equations were discretized by using computation fluid dynamics (CFD) and finite-volume method - central differencing scheme, then solved using Gauss-Seidel Iteration method on uniformed grid with VISUAL BASIC code. Effects of equivalence ratio and initial temperature of fresh gases (air – fuel mixture) were investigated for three types of fuel Methane, Propane and Butane. Also the flame speed and flame temperature were experimentally measured for air – fuel (Methane, Propane, Butane and LPG) mixtures. The burning velocity was calculated depending on the flame speed and flame temperature measuring. The flame speed and flame temperature were measured by using optical technique. Effects of equivalence ratio and initial temperature of fresh gases (air – fuel mixtures) on flame speed and flame temperature are investigated experimentally. Results were generated for the detailed description of the local fluid flow and heat transfer characteristics including temperature, axial velocity, density and mole fractions profiles. For example the flame speed reached 274.4 cm/s as a maximum value at Ø=1.1 for propane air mixture, and flame temperature comparison give a good agreement between theoretical and experimental results at rich mixtyre
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
Concerning commercial and residential buildings, one of the major parts related to water supply systems is the water storage tanks. For gravity- fed buildings, the tanks must be installed on the roof. In Iraqi summer, the temperature of water in storage tanks reaches above 50 °C due to high solar intensity, which makes it inappropriate for domestic usage. One of the proposed solutions to overcome this problem is feeding the hot water into an earth-water heat exchanger (EWHE) which consists of a set of buried pipes installed underground level to reduce its temperature. The storage tank and the earth-water heat exchanger were studied experimentally and theoretically by using ANSYS 20/FLUENT software to estimating the water temperature in the storage tank and the temperature of the water leaving the EWHE. The most important results obtained theoretically and experimentally that when using pipe length, pipe diameter, and mass flow rate of 100 m, 0.016 m, 0.7 LPM respectively, at a depth of 3 m, the water temperature decreases by about 15 °C. Also, the results have shown a good agreement between the experimental and theoretical works. One can conclude that an earth-water heat exchanger is an effective way to decrease the temperature of the storage water to an acceptable level for domestic usages.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
A new model of bubble dynamics is constructed using linear wave equation, including effects of variation of the gas temperature inside the bubble and the liquid temperature near the bubble, and effects of evaporation-condensation of the liquid vapour at the bubble wall. The liquid is assumed water and the gas inside the bubble is only vapour (neglecting non-condensable gas). The temperature inside the bubble and the liquid temperature are numerically calculated by solving the energy equation both inside (vapour-phase) and outside (liquid-phase) the bubble (using finite difference method). The pressure inside the bubble is obtained numerically without assuming that it follows any assuming relation. The results reveal that the bubble radius, the liquid temperature, and the pressure and temperature inside the bubble change with time periodically. Both the pressure and temperature become higher when the radius becomes minimum. The present theoretical result is compared with data from other reference and with another theoretical model to check the validity of the present model. The calculated result approximately fits with the data of the previous studies.
The heat lost from gas turbine power plants with exhaust gases represents the most important source for lowering its thermal efficiency. Also, the gas turbine thermal efficiency affected significantly with the ambient surrounding temperature. Al-Najybia gas-turbine power plant in Basrah, Iraq is choosing as a case study. The power plant consists of four units with a capacity of 125 MW for each unit. In the present study, all the calculations are performed for one unit only. Firstly the thermal impact is studied in terms of energy analysis for Al-Najybia gas turbine power plant (GTPP) for different ambient temperature for twelve months. Also, the economic loss a companied the heat lost with exhaust gases for different ambient temperature are estimated. Secondly, the thermo-economic improvement from coupling the GTPP with a heat recovery system is studied. For gas-steam combined cycle, the performance and economic analysis are performed. The results show that, the output power and thermal efficiency are decreased by 0.97 MW and 0.0726% respectively for each unit temperature rise of the ambient temperature. For the combined gas-steam power plant the percentage increasing of the thermal efficiency is approximately 46.4%. The results indicate the combined cycle power plant (CCPP) is very important to increase electrical capacity. From the economic analysis, the economic gain due to using HRB is 75757 $ per month.
Solar chimney (SC) together with earth to air heat exchanger (EAHE) is being employed as a low-energy consuming technique to remove undesirable interior heat from a building in the hot seasons. A numerical program "FLUENT 6.3 code" of an earth to air heat exchanger (EAHE) is studied for predicting the outlet air temperature and cooling potential of these devices in Basrah climate. Theoretical analyses have been conducted in order to investigate the ventilation in a solar chimney. The investigation into the viability of Low Energy Earth Pipe Cooling Technology in providing thermal comfort in Basrah. The demand for air-conditioning in buildings in Basrah affects the country escalating energy consumption. Therefore, this investigation was intended to seek for an alternative passive cooling to air-conditioning. The passive technology, where the ground was used as a heat sink to produce cooler air, has not been investigated systematically in hot and humid countries. A sub-soil temperature model adapted for the specific conditions in Basrah is presented and its output compared with CFD modeling. The results have shown that the potential of Earth Pipe is providing lower output temperature of air inlet to the room. We found that the resulting temperature at the buried pipe outlet decreases with increasing pipe length, decreasing pipe diameter, decreasing mass flow rate of flowing air in the pipe and increasing depths up to 4m.
In this research work, the influence of cutting parameters and drill point angle on the temperature distribution in dry drilling of stainless steel AISI 304 was numerically investigated by using FE method based on DEFORM-3D V.11 commercial software. Two cutting tools of 10 mm diameter but different in point angles, one is 110° and the other is 118°. These tools were imported from specific website in a format of STL and inserted in the program during modeling of cutting tools. The material of the cutting tools is selected as high-speed steel. The workpiece model is created as cylindrical shape with 50 mm diameter and 5 mm thickness. The cutting parameters are selected as three cutting speeds (100, 200, and 300) rpm, with three feed rates (0.15, 0.25, and 0.35) mm/rev. The depth of hole is fixed for all simulations (3 mm). The percentage of increase or decrease in the resulted temperature according to the various cutting parameter was also calculated and discussed. The best cutting performance of tools according to the change of point angles was also investigated. The results provided a significant influence of cutting speed and tool point angle on the temperature generated in the machined models and very small influence of feed speed on the workpiece temperature.
Lithium-ion batteries' physical properties classify them as one of the most important sources of clean energy that overcome the need for fuel usage. The rated operating temperature and its uniformity are of the main demands of Lithium-ion batteries. In this survey, several types of studies have been reviewed with the aim of understanding the thermal management systems used to control the temperature of lithium-ion batteries and their uniformity in the battery pack. They are represented by active and passive systems, as well as the hybrid system, which integrates each of the two mentioned systems into a system to obtain the best thermal performance. Active cooling systems were classified due to the type pf coolant used to air and liquid system, meanwhile passive system classified to PCM and heat pipe system. The survey reveals that the air-cooling of lithium-ion battery pack is better than the use of liquids. About 74% of the reviewed works prefer the use of active strategies. The working temperature under normal conditions should be within -20 to 60 °C, meanwhile the optimum range is 15 to 35 °C. The maximum temperature difference between batteries in the pack is preferred to be 5 °C or less.
This study presents both experimental and theoretical investigations of an absorption refrigeration system using environmentally friendly working fluids, specifically the acetone–zinc bromide (Acetone/ZnBr₂) pair. The system was designed to operate under outdoor climatic conditions in Hilla City, Iraq, utilizing hot water as the heat source. Performance evaluation was carried out under various operating conditions, including changes in heat source, absorber, condenser, and evaporator temperatures. Experimental testing was conducted during September 2019. The results indicated that the coefficient of performance (COP) of the absorption cooling system ranged from 0.13 to 0.487, with an evaporator temperature drop of approximately 16 °C. Condensation and absorption temperatures remained below 41 °C, while the maximum driving water temperature reached 80 °C. A steady-state theoretical model was developed using the Engineering Equation Solver (EES) program, applying mass and energy balance equations to predict operating parameters such as temperature, pressure, and COP. Model predictions showed good agreement with the experimental measurements. Furthermore, the results confirmed that generator temperature has a significant influence on overall system performance.
The conjugate natural convection-conduction heat transfer in a domain composed of nanofluids filled porous cavity heated by a vertical solid wall is studied under steady-state conditions. The vertical left wall of the solid is kept isothermal at hot temperature Th. The vertical right wall of the solid is in contact with the nanofluid saturated porous medium contained in the cavity. The right vertical wall of the cavity is kept isothermally at the lower temperature Tc. The upper and lower horizontal walls are kept adiabatic. The governing equations of the heat transfer in the solid wall and heat and nanofluid flow, based on the Darcy model, in the nanofluid-saturated porous medium together with the derived relation of the interface temperature are solved numerically using the over-successive relaxation finite- difference method. A temperature independent nanofluids properties model is adopted. The investigated parameters are the nanoparticles volume fraction (0-0.2), Rayleigh number Ra (10-1000), solid wall to base-fluid saturated porous medium thermal conductivity ratio kwf (0.1, 1, 10), and the solid wall thickness D (0.05-0.5). The results are presented in the conventional form; contours of streamlines and isotherms and the average Nusselt number. At a very low Rayleigh number Ra=10, an enhancement in heat transfer within the porous cavity with is observed. Otherwise, the heat transfer may be unchanged or deteriorated with depending on the wall thickness D and the conductivity ratio kwf.
By using linear wave equation a new model of bubble dynamics in acoustic field is constructed including effects of thermal conduction both inside and outside a bubble, and non-equilibrium evaporation and condensation of water vapour at bubble wall. The liquid temperature at bubble wall is numerically calculated by solving the heat conduction equation (without assuming a profile of liquid temperature). It is including effect of the latent heat of non-equilibrium evaporation and condensation at bubble wall. It is concluded that the liquid temperature increases to the same order of magnitude with that of the maximum temperature attained in the bubble at strong collapses. It is caused by the latent heat of intense vapour condensation and by the thermal conduction from the heated interior of the bubble to the surrounding liquid. The intense vapour condensation takes place at strong collapses because the pressure inside the bubble increases. The comparison is given between the calculated result and the experimental data of radius-time curve for one acoustic cycle. The calculated result fits well with the experimental data.
Solar energy can only be used when it's sunny outside. Therefore, solar heating is only efficient during the day and decreases at night or on overcast days. Consumer energy needs have a distinct seasonal structure, and solar energy cannot completely meet those needs. In order to satisfy customer demand, energy storage is essential. In order to maximize the use of solar energy and to increase the energy and efficiency of the solar absorption system, superior thermal properties of sophisticated materials, such as phase change materials, are important [1]. In the current study, 20 kg of phase change material (PCM) is integrated with solar water heating and fed into a storage tank to enhance the solar water heating efficiency. Helical coil heat exchangers were added to the storage tank as an external load. The trials were conducted in four separate months (September 2021, April, May, and June 2022) that were chosen on the first day. The effectiveness, heat gain, and significance of the phase change material in increasing heating efficiency throughout the day were studied using a range of variables, including water volume flow rate (2, 3, 4, 6, and 8 L/min) and inlet water temperature (25, 30, and 35 °C). The results showed that, given an initial temperature of 25 °C, the daily efficiency range, was 0.58 to 0.65, and that the daily final outlet temperature was enhanced outlet temperature over 65 °C. Additionally, on all test days, the heat released by the phase change material was audible in the evening and increased the utilization time.
The transition to electric vehicles (EVs) is a crucial step towards mitigating climate change and addressing the global energy crisis. The increasing use of lithium-ion batteries in EVs is attributed to their superior power density and efficiency. However, ensuring optimal battery performance and safety necessitates effective thermal management due to the significant heat generated during operation. Current cooling systems face challenges in maintaining the desired temperature range and uniformity. This paper reviews the state-of-the-art techniques in battery thermal management, focusing on phase change material (PCM) cooling and different cooling methods. This study, in accordance with its developments, compares the advantages and limitations of various cooling methods as potential solutions for next-generation EVs. It highlights the potential of method cooling, which, while promising, needs further research to establish its commercial viability and aims to guide future advancements in battery thermal management for next-generation EVs. Under both typical and extreme usage scenarios, direct cooling may enhance the necessary battery performance and serve as an innovative method for managing the temperature of electric vehicle batteries. The primary challenge of this technique lies in its suitability for commercial application. This article is organized to cover the thermal properties of lithium-ion batteries, the main issues associated with lithium-ion battery heat, a discussion of reversible and irreversible heat generation and their effects on battery performance, as well as strategies for preventing and mitigating thermal runaway in battery systems. Finally, it summarizes the key recommendations for future research on battery thermal management.
Polyethylene terephthalate (PET) was prepared from (PET) flakes and 25% of NaOH solution were added to in tri-neck flask, the reaction run for six hours at temperature (100-130) oC and the precipitate was reacted with ethylene glycol at temperature (130-160) oC. IR spectrophotometer was used for the diagnoses of (PET). Differential scanning calorimeter (DSC) is used to indicate glass transition temperature Tg, the melting temperature Tm and the heat absorbed. Part hundred ratios (phr,s) of (PET) rather than dosage of PET in gms. To concrete cubes were added to study its effect on concrete properties. Additives of (phr,s) impart performance such as increased cement dispersion, and enhance the performance of concrete which was appeared in maintaining a lengthening or slow the setting time that meets product and job needs. Maximum and minimum compressive strength is 43.7 MPa and 30.0 MPa at 0.3 gm. and 0.1 gm. respectively.
The aim of the present study is to perform analytical simulation for the single-effect LiBr- water absorption refrigerating system (ARS) in order to scan for all possibilities of operating the cycle among most available operating variables to obtain the best performance and determine what are the proper parameter needed to be changed so that the refrigerator can operate using ambient air instead of water and cooling tower accessories to dissipate the hear at the condenser and absorber. The COPs of the cycle was obtained as a function of the different temperature of the cycle and solution concentration. The performance characteristics of the cycle were examined by changing the temperature of the heating source supplied at the generator, the temperatures at the condenser, absorber, and evaporator. It can be concluded that the concept of air cooled absorption chiller is feasible with coefficient of performance of 0.43 10 0.79 depending on the evaporator temperature for any cooling capacity in some applications, where the chilled water supply temperature is not necessary to be too cold.
A numerical simulation of the effect evaluation of heat loss and temperature distribution along the wellbore is performed, for two models, the first is an open hole (without perforation) and the other is a perforated vertical wellbore. In this study, the Computational Fluid Dynamics (CFD) software code ANSYS FLUENT 15.0 has been used, for simulate a model of 3-D turbulent flow with stander k-ϵ model. The results of this show that, increasing the heat losses leads to an increase in the temperature gradient, while the temperature gradient decreases with increasing inlet main velocity. Also, the temperature of the produced crude oil decreases with increasing the length of the wellbore.
Natural convection heat transfer in porous cavity with arc shape wall filled with nanofluid is studied numerically. The right arc shape wall of the cavity is heated at constant temperature (Th) while the left wall is kept cold at constant temperature (Tc), and the other horizontal walls are thermally insulated. The governing equations of the heat transfer and nanofluid flow are solved Flex PDE software. A temperature independent nanofluids properties models are adopted. The investigated parameters are the nanoparticles volume fraction Ø= (0-0.2), Rayleigh number Ra (10-1000) and arc center Ce (1-∞). The results are presented by contour of streamlines, isotherms and the average Nusselt number. The results have showed that the average Nusselt number decreases with increasing Ce and increases with increasing Ra and Ø.
In this paper friction stir welding process has been studied whereby utilized FEM method (Ansys software ver. 20). The main effective parameter in this process were rotational speed, linear speed, tool shoulder radius, heat transfer coefficient and clamping percentage to study their influence on represent temperature, von misses stress and frictional stress distribution. Because of the difficulty to obtained the number of the simulation cases in order to get the most important results, Taguchi L27 orthogonal array was apply to reduce the total number of the simulation cases. Pure copper (t = 3.18 mm) material type was applied as work plate material. ANOVA statistical tool was utilized to achieved the optimization process after the simulation cases done. Percentage of contribution of each parameter can be obtained by ANOVA table and mean of S/N ratio plot. Validation process was achieved between the Current study and experiment work in the temperature distribution field with percentage of error 2.7 %. From optimization result It is found that the optimum condition in order to obtained good results for temperature was rotational speed of (450 rpm), linear speed (2.75 mm/s), tool shoulder radius (7 mm), heat transfer coefficient (300 w/m 2 K), clamping distance percentage (40 %). And for von misses stress was rotational speed of (550 rpm), linear speed (3 mm/s), tool shoulder radius (7 mm), heat transfer coefficient (300 w/m 2 K), clamping distance percentage (20 %). While for frictional stress was rotational speed of (450 rpm), linear speed (2.5 mm/s), tool shoulder radius (7 mm), heat transfer coefficient (300 w/m 2 K), clamping distance percentage (30 %).
A household refrigerator represents an essential device for all houses nowadays. The electric energy consumed by the refrigerator and the fluctuation of the temperature inside the fresh food cabin is the main two problems affecting its performance. Incorporating phase change material (PCM) inside the refrigerator is one of the solutions for the previous mentioned problems. In the present study, a water PCM is added to the cabinet of 220-litters double door refrigerator. The PCM (0.5 ml of water) is added at three different locations, touch the front of the evaporator part inside the cabin, touch the rear of the evaporator part in the cabin, and far away from the evaporator part inside the cabin. The location of the PCM determines how much energy is released and stored from the evaporator. The use of phase change material (PCM) touch to the evaporator increases the rate of heat transfer due to the conduction method being used throughout the whole heat transfer process from the evaporator to the phase change material (PCM), which raises the refrigeration system's COP (coefficient of performance). The experimental test period is 24 hours for each day. Firstly, the refrigerator is tested without using PCM, and the power consumption, the temperatures at different points for the refrigerator, suction pressure, discharge pressure, the ambient temperature, and the time on period and time off period of the compressor are measured. Secondly, for same testing period all previous parameters are measured with using PCM at different locations inside the refrigerator. The results show that, adding the PCM (water) behind the evaporator led to increase the COP by 21.97%, increase the compressor off time by 73 minutes, reduction in power consumption of 14.4%, decrease of exergy losses of the system by 8% and temperature fluctuation reduced inside the fresh food cabin, that enhance the quality of stored food. Adding the PCM front the evaporator improve the previous parameters but less than that of the first case. The third location, adding the PCM far away from the evaporator has no improvement on the refrigerator's performance.
The present work includes a study on the effect of loading rubber waste into cement mortar on the thermal and mechanical properties of a thermal insulator.The experimental work of the study included the preparation of ten models of 35 mm diameter and 5 mm thickness. Portland cement and natural sand were used as a matrix and rubber waste (extracted from the consumed tires) as a filler was added in weight percentages ( 5% ,10% ,15% ,20% ,25% ,30% ,35% ,40%,45% and 50%). Water was also used as a binder.Also, the experimental work included conducting a thermal conductivity test using Lee’s Disk method, and a hardness test using the Shore scale. The theoretical side included extraction of empirical equations, depending on the experimental results. The thermal conductivity equation was for two variables, temperature and mass fraction. While the hardness equation was for one variable, mass fraction. Theoretically determined heat capacity was extracted using the equations of the composites. Based on the empirical equations of thermal conductivity and hardness and using the technique of multi- objectives genetic algorithm, the optimum values of temperature and mass fraction were extracted, which achieve the best thermal insulation of the mortar. The results showed a significant decrease in thermal conductivity. The reduction in thermal conductivity was (90.3%) at 5% and reduced to (95.73%) at 50%. The specific heat capacity was increasing as the percentage of rubber waste increase. The results also indicated a decrease in hardness. The optimal value of thermal insulation was (0.02658 W/m 2 .ºC ) as a thermal conductivity and (58.07 N/m 2 ) as a hardness, at temperature (50°C) and mass fraction (27.764%) of rubber waste.
Retained Austenite (RA) has great deal with the me- chanical properties of high strength low alloy steel. Therefore, in this paper, Retained Austenite volume fractions have been evaluated in AISI4340 alloy steel using two well-known meth- ods, X-Ray diffraction (XRD) and magnetic measurement methods. The specimens were heat treated using different heat- ing temperature and different cooling rate (different quenching media). A comparison between the results of two methods proved that there results were approximately Identical .The results show that Retained Austenite formation increase as heating (Austenizing ) temperature increase for the same quenching media ,as well as ,it increases by increasing cooling rate . The maximum amount of Retained Austenite found as (27.2 Wt %) which recognized when the specimens heated up to 1000˚C then quenched in Water while the minimum amount of Retained Austenite found as ( 7.06 wt%) when the specimens heated up to ( 800 ˚C) then quenched in Sand. Hardness tests using Vickers and Rockwell methods were used and the results show that hardness values decreased with increasing heating temperatures and the maximum Vickers micro-hardness and Rockwell hardness numbers were equal to (121.8HRB) and ( 516.35 HV) which were detected when heating up of the speci- mens were up to 800 ˚C then quenched in water. Tensile tests show that increasing cooling rate lead to increasing in Strength due to increasing of hardness which in turn, leads to increase in yielding points and ultimate strengths. Retained austenite effects on microstructure were investigated using scanning electron microscopy (SEM) and optical microscopy and the results show that at low cooling rate the microstructure consist of bainite and/or martensite phase with small amount of re- tained austenite, while, increasing heating temperature and cooling rate results in microstructure consist of martensite and retained austenite phases.
Solar energy is the most suitable among all renewable energy options for competing with fossil fuels in desalination due to its ability to utilize both heat and power for the process. In this study, the Parabolic Trough Solar Collector (PTSC) for powering a Single Stage Flash (SSF) desalination unit was proposed for Basrah city climate, Iraq. The desalination system comprises two directly coupled sub-systems: the PTSC and the SSF desalination unit. The preheated feed brine water coming from condenser was used as a Heat Transfer Fluid (HTF) for PTSC, which gets heated to a desired temperature referred to as the Top Brine Temperature (TBT). The numerical simulations were performed via EBSILON professional 16.02 (2022) software. The effects of TBT, mass flowrate of feed brine water to get the desired TBT, solar collector area, and vacuum pressure inside flash chamber on the performance of the desalination system was studied. A major finding of the current study can be summarized as follows: The collector efficiency is enhanced eventually as TBT increases. The maximum values of distillate water in June are around 5.5, 4.56, 3.69, 2.75 and 1.85 kg/h for 12.408, 10.434, 8.3472, 6.26, and 4.1736 m² collector area respectively, when TBT 107 °C and vacuum pressure 40 kPa. For 1.598 m² collector area, the total distillate in the 1st of June amounted to 7.9 kg, with an average production rate of around 0.7 kg/h. The solar SSF system's productivity per solar collector unit area at 20 kPa, 15 kPa, and 10 kPa vacuum pressures was 4.7 kg/day/m², 5.3 kg/day/m², and 6.25 kg/day/m², respectively. The average Performance Ratio (PR) values are determined to be 0.694, 0.577, and 0.491 for 10 kPa, 15 kPa, and 20 kPa, respectively. These results are very acceptable when compared with an existing literature.
The efficiency of gas turbine units is highly affected by the variation of ambient temperature. Increasing the ambient temperature decreasing the efficiency of gas turbine. Cooling the inlet air to the compressor of the gas turbine units is an essential and economical technique for improving its efficiency. Al-Rumaila gas turbine power plant was located in Basrah city, Iraq, which is characterized by its hot climates for more than six months during the year. A novel upstream inlet air cooling system was applied and tested for Rumaila gas turbine power plant. This article represents a thermo-economic evaluation of applying upstream inlet air cooling system. The analysis is based on the test results for operating single unit of Rumaila gas turbine power plant using upstream inlet air system for cooling. The test was performed during July of 2019 for 90 minutes of operation period with ambient temperature of 45 °C. The evaluation analysis shows that, the power output increased from 217.71 MW to 250.11 MW during the period test with percentage increase in power by 15%. This increase in power output led to net economic gains is approximately 1000 $/h.
Mixed convection heat transfer of air in a horizontal channel with an open square cavity is studied numerically. At the center of the cavity, it is an insulated rotating circular cylinder for enhancing the efficiency of heat transmission, the location of the inner cylinder is changed vertically along the centerline of the cavity. Heat is applied to the bottom wall of the cavity at a constant temperature, and the other walls are adiabatic. The flow is steady-state, laminar, and incompressible. Using computational fluid dynamics (CFD) and the commercial software program FLUENT 2019 R1, the equations of continuity, momentum, and energy are numerically solved. The angular velocity of the cylinder range is (0 . 5 ≤ ω ≤ 4) rad/sec in a counterclockwise direction, the Richardson number range ( Ri = 0 . 1 , 1 , 10), Reynolds number is 100 and the cylinder location is ( C = 70 , 50 , 30) mm. The airflow Prandtl number is taken as ( Pr = 0 . 7). The effect of various positions of the rotating cylinder has been examined through the visualization of streamline and isotherm contour, as well as the distribution of the average Nusselt number of the heated surface. The results indicate that the flow field and temperature distributions inside the cavity are strongly dependent on the rotating circular cylinder and the position of the inner cylinder.
Pipelines are one of the most convenient and effective ways of transporting petrol over a long distance. The environment applies, beyond extremely high external pressures, low temperatures and intensive corrosive process, the occurrence of defects on the pipe body, which compromises the structural integrity of pipelines leading to catastrophic failures. The main modifications concern the mechanical resistance, toughness at low temperatures weld ability and resistance to embrittlement related to hydrogen. Among mechanical characteristics, the fracture toughness is very important for pipeline steels in design and safe assessment. Aiming to enhance the reliability and operation of complex pipelines system, a study based on the mechanics of the elastoplastic fracture in order to determine better prediction of the fatigue life. The materials tested here are API 5L X42 and X52 micro alloyed steels, as well as to evidence the toughness resistance of these materials. Results indicated that both X42 and X52 steel behave in a similar way and in all cases a slight increase of the transition temperature was found. The characteristic toughness value shows an evident loss in mechanical performances if compared to the uncharged one.
The incorporation of thermal energy storage materials (TESMs) into solar energy systems is a factor that boosts the performance of these systems. In this paper, an experimental study was addressed for enhancing the heat pipe’s thermal performance that works with an Evacuated Solar Tube Collector with Heat Pipe (ETCHP) as a solar water heater system. This is done by adding micro-zinc oxide (ZnO-MP) to the paraffin wax integrated as TESM into the evacuated tube (ET) of the system, where the evaporator section of the heat pipe is completely submerged within the micro-enhanced paraffin wax. Three experimental prototype rigs with one evacuated tube were designed, built, and tested to do the investigation. The most important parameters that have been studied in this study are the thermal resistance and the temperature distribution pattern along the heat pipe. The results show a clear indication of the decrease in the thermal resistance of the heat pipe of the proposed system compared to the system in which pure paraffin wax was incorporated. Also, it was noticed that there is a significant improvement in the temperature distribution along the heat pipe due to the improvement in the conductivity of the micro-enhanced wax compared to the pure wax.
4-Stearoylresorcinol was prepared by acylation of resorcinol with stearoyl chloride in the presence of zinc chloride as catalyst in a batch reactor. The temperature range of reaction was (50-80)°C. The rate of acylation increased with temperature up to (70°C). The conversion of reactants appeared to follow second order kinetic model. The reaction rate constant was (0.0031 1/mol.min) and was higher at higher temperatures. Activation energy was (16.8258 kJ/mol). The optimal catalyst concentration was (2.9936 mol/l). Also, a quantitative relationship was derived to represent the weight of the product as a function to the reaction variables. The quantitative relationship gave mean deviation equal to (5%). The product concentration was measured by UV spectroscopy.
The thermoelectric behavior of different materials under various conditions has been investigated numerically by using the heat transfer module of the COMSOL Multiphysics software platform. A simulation study of the thermoelectric materials (TEM) performance was created by altering the current applied from 0.1 to 1.0 A and setting the hot side temperature (T H ) as 273 K. The impact of different performance metrics, such as cold side temperature and output voltage, has been proven and investigated. It has been shown that the material of the thermoelectric legs', length of leg, and thickness of electrodes significantly impact the thermal and electrical performance of the thermoelectric (TE) module. Appropriate ranges have been studied in the simulation, such as the amperage values applied to the unit as mentioned above, the length of the leg within a range of 1 to 8 mm, and the thickness of the electrode with different values of 0.1 to 0.5 mm, which will achieve excellent performance for the Thermoelectric unit. Modeling and simulation results demonstrated and revealed the optimal and potential use of bismuth telluride (Bi 2 Te 3 ) as well as lead telluride (PbTe) as suitable for Peltier cooling applications. As for the use of cobalt triantimonide (CoSb 3 ), it is in contrast to the two previous metals, as it is effective and appropriate if applied to power generation. The results are validated with another study from the literature, and there is an excellent agreement with an error rate that does not exceed 0.164%.
This study presents three-dimensional numerical simulations of single-phase laminar flow and forced convection heat transfer of water in a five-layer microchannel heat sink with two channel configurations: radial arrangement and parallel divergence channels. The thermal performance and pressure drop characteristics were evaluated under identical operating conditions, including a constant mass flow rate of 3.925 × 10⁻⁴ kg/s and a uniform heat flux of 90 W/cm². The results indicated that the radial microchannel configuration significantly enhanced both hydrodynamic and thermal performance compared with the parallel divergence design. Specifically, the pressure drop was reduced by approximately 32.5%, the overall performance index increased by about 1.5, and improved temperature uniformity across the heat sink was achieved. These findings demonstrate the superiority of the radial microchannel arrangement for high-heat-flux thermal management applications.
Parallel flow microchannel heat exchanger performance was numerically investigated, for laminar, 3-D, incompressible and steady state flow with slip flow and temperature jump conditions. The continuity, Navier-Stokes equations and the energy equations for the hot and cold fluids were solved by using finite volumes method and SIMPLE algorithm method with FORTRAN code to obtain the velocity and temperature distributions for the two fluids and the separated wall between them. The main investigation parameter that affected on the performance and effectiveness of heat exchanger are: Reynolds number Re, thermal conductivity ratio Kr, Knudsen number Kn, thickness of separating wall, heat capacity ratio Cr and aspect ratio α. Increasing of Reynolds number, Knudsen number, thickness of separating wall, heat capacity ratio and aspect ratio each separately leads to decrease the effectiveness while increasing of thermal conductivity ratio up to 10 leads to increase the effectiveness. Also, it is found that friction number and Nusselt number both decreases with increasing Knudsen number.
The panel absorbed solar radiation and majority of this radiation is transform into a heat, and it is usually wasted and useless. At higher cell temperature, the current out of the cell has an unnoticeable rise, but the voltage value will drop significantly, resulting in a reduction in maximum power produced. The cooling method is therefore beneficial to keep the panel at the operation temperature. A simulation model is developed using COMSOL Multiphysics software version 3.5 software to investigate the enhancement in performance of a PV water cooling module (PVW module) based on a passive and simple cooling technique using a wetted cotton porous wick attached on the PV panel's back side and compare with uncooled PV panel (PVREF module). Unsteady, laminar and 2-D, the flow in the proposed modules is assumed. The input parameters were taken from a real weather condition was perform in Najaf-Iraq. The effect of variation of mass flow rate is also studied in the present work. Good agreement was obtained for PVREF module with previously researches.
The aim of this work is to experimentally study the influence of fiber prestress and curing temperature on the tensile and flexural properties of carbon fiber-epoxy composite. Adaptive Neuro-Fuzzy Inference System model was used to predict the effect of fiber prestress and curing temperature on the tensile strength, tensile modulus, flexural strength and flexural modulus of carbon fiber-epoxy composite. It was found that, the best membership functions for predicting the tensile strength, tensile modulus and flexural modulus are Gaussian membership functions with 4 number of membership function, and for predicting the flexural strength are generalized bell membership functions with 4 number of membership functions. From the comparison between the experimental and predicted results of carbon fiber-epoxy composite properties, it is found that the prediction results of this model show a good agreement with experimental results.
This study numerically investigates natural convection of Cu-water nanofluid in a square cavity subjected to a cooling air stream along the left wall, with the right and bottom walls maintained at cold (TC) and hot (TH) temperatures, respectively, while the top wall is adiabatic. The nanofluid flow is assumed laminar and governed by the Boussinesq approximation. The governing equations are solved using the finite volume method in ANSYS FLUENT. Simulations are performed for nanofluid volume fractions (φ = 0–0.16), Rayleigh numbers (Ra = 10³–10⁵), and free stream Reynolds numbers (Re∞ = 10³–10⁴). The effects of these parameters on stream function (ψ), temperature contours (θ), and average Nusselt number (Nuavg) are analyzed. Results indicate that heat transfer rates increase with higher φ, Ra, and Re∞. Increasing φ and Ra enhances circulation within the cavity, whereas higher Re∞ induces secondary vortices and reduces circulation in the primary vortex. Comparisons of local Nusselt numbers and temperature distributions with previous studies show good agreement, with maximum errors of 14.28% and 3.2%, respectively.
The mechanical properties of low alloy steel are significantly influenced by retained austenite (RA). Consequently, using the X-Ray diffraction (XRD) measurement method, the retained Austenite volume fractions in AISI4330 alloy steel have been assessed in this article. The specimens underwent heat treatment at various heating temperatures (800 ֯ C, 900 ֯ C,1000 ֯ C) and cooling rates (Water and Oil). The findings demonstrate that retained Austenite formation rises with rising heating (Austenitizing) temperatures for the same quenching media as well as with rising cooling rates. The specimens were heated to a temperature of 1000 °C and then quenched in water, yielding the highest amount of retained austenite (7.733 wt%), and the lowest amount (1.977 wt%), which was obtained when the specimens were heated to a temperature of 800 °C and quenched in oil. The Vickers method was employed to conduct micro-hardness testing, and the results demonstrate that hardness values are reduced as heating temperatures increase. Optical microscopy was used to investigate the effects of retained austenite on the microstructure. The results show that bainite and/or martensite phases with a small amount of retained austenite dominate the microstructure at low cooling rates, whereas martensite and retained austenite phases dominate the microstructure at higher heating and cooling rates.
The desalination market is gradually growing as a result of the significant water scarcity in various regions throughout the world. Concentrated solar power (CSP) can be used to power distillation, which is an effective method for addressing water shortages in areas where there is both a severe lack of water and abundant direct normal irradiation. CSPs are ideal candidates for the advancement of desalination technologies due to their capacity to produce both thermal and electricity energy. This review article offers a comprehensive of the current status of cutting-edge CSP-desalination systems. The paper reviews previously published studies conducted by researchers in the field of multi-effect desalination using concentrated solar collectors, and they are classified into two main types. Exclusively freshwater generation and freshwater / electricity cogeneration. In addition, the paper reviews conventional desalination. This review illustrates that there are numerous prospective methods for integrating desalination systems into CSPs. Potential areas for future investigation in CSP-desalination systems. In particular, the most significant obstacles to be surmounted are lowering the costs and efficiency improvements of solar repayment and desalination equipment. A potential method to expedite the commercialization of these plants is to develop innovative strategies that optimize thermal efficiency and reduce costs. Environmental factors (solar radiation intensity, ambient temperature and wind speed) and design factors (solar field area, number of mirrors, number of stages, steam temperature, steam quantity and pressure) are the main effective parameters that affect the distilled water production process. In general, the CSP desalination systems are environmentally and technically appealing; however, there remains substantial progress to be made in order for these plants to be commercially viable.
A mathematical model to analysis three–dimensional forced convection turbulent flow in a novel solar air heater integrated with multiple rectangular capsules filled by paraffin wax-based on phase change material PCM was implemented. The investigations were performed under three airflow speed of (0.6, 1.2, and 1.8) kg/min and average solar flux of 625 W/m 2 . The results revealed that the delaying melting time and also lower the melting temperature of PCM by increasing airflow speed during the charging process. As well as, the freezing period is dependent on the airflow speed by inverse relation. Also, the data results represent that the useful energy rate and thermal storage efficiency were a strong dependence on the airflow speed. Moreover, it can be detected that the optimal freezing time and the air temperature rise of the heater were reached about 210 minutes with (12 – 1.5 °C), 150 minutes with (7.5 – 1.4°C), and 120 minutes with (5.5 – 1.5 °C), at airflow speed of 0.6, 1.2, and 1.8 kg/min, respectively, which can be used at night to supply some applications by thermal energy such as heating buildings and drying agricultural crops.
Hydrodynamics and heat transfer in a fully developed laminar incompressible reciprocating channel flow subjected to a constant heat flux have 'been investigated analytically using similarity transfo1mat ion. An exact analytical solution for the velocity, local, and bulk temperature as well as the Nusselt number has been obtained. The effect of the parameters Pr, Ao, y, and X/Dh on u, T, Tt, Nux, and Nux are presented. The results showed that the local Nusselt number is increased with increasing Womersly number (A.) while the dimensionless temperature is increased with Womersly and decreases with amplitude (Ao). The Prandtl number has a significant effect on the local Nusselt number. The results were found in very good agreement with those obtained numerically using the finite volume method. The comparison with the experimental results of other authors gave a reasonable identification.
The polyethylene terephthalate (PET) was prepared from PET flakes of empty local water drinking bottles and diagnosis by infrared spectroscopy (IR). The glass transition temperature, melting temperature T m and heat capacity were indicated by differential scanning calorimeter (DSC). Part hundred ratios (phr , s) of (PET) were added to study its effect on concrete properties. Additives of (phr) impart performance such as increased cement dispersion, enabling drastically reduced water requirements. Enhance the mortar cubes performance; depend on the compatibility of cement with PET. Porosity of mortar cubes with cement, sand and added PET products were calculated. Maximum and minimum Compressive strength were calculated 58.76 MPa, and 24.0 MPa at phr 0.04 and 0.07 of PET with cement. And PET with cement and sand were calculated 16.5 MPa and 4 MPa at dosages 0.03 gm. and 0.08 gm. The relative dosages in calculating porosity percentages are (0.06, 0.1 and 0.3) gm.
Plants and agriculture are important in Iraq and the world because they are among the essential basics of life; their importance lies in several fields, such as industry and food. Plant diseases are the first direct influence on plant production and the Iraqi economy. The primary contribution of this work is developing an efficient early warning system for tomato plant diseases based on readily available environmental data, demonstrating the usefulness of machine learning methods in real agricultural environments. This research investigates the use of artificial intelligence (AI) for the early prediction of tomato diseases in Iraqi agriculture, based on temperature and humidity data collected from Salah al-Din Governorate. Two major diseases were studied: Tomato Yellow Leaf Curl Virus (TYLCV) and late blight. The data were pre-processed and used to train predictive models, including linear regression and Random Forest Regressor (RFR). Results show that RFR outperformed linear regression, achieving a lower Root Mean Square Error (RMSE) of 0.053852 and a Mean Absolute Error (MAE) of 0.45000, indicating its superior accuracy in predicting disease occurrences.
In the present research, a Matlab program with a graphical user interface (GUI) has been established for studying the performance of a solar tower power plant (STPP). The program gives the ability for predicting the performance of STPP for different tower dimensions, ambient operating conditions and locations. The program is based on the solution of a mathematical model derived from the heat and mass balance for the tower components. The GUI program inputs are; tower dimensions, solar radiation, ambient temperature, pressure, wind velocity, turbine efficiency, emissivity and absorptivity for collector and ground and thermal conductivity and thickness for ground. However, the GUI program outputs are; temperature and pressure differences across the collector and tower, velocity in the tower, density of air in collector outlet, mass flowrate of air, efficiency for collector and tower, the overall efficiency and output power of STPP. The effect of the geometrical dimensions of STPP and some climatic variables on the plant performance was also studied. The results show that the output power increases with increasing the collector diameter, chimney diameter and solar radiation by an increasing of 0.282 kW/m, 0.204 kW/m and 0.046 kW/(W/m2) respectively.
In the operating of TEG- dehydration unit in Central Rumaila Compression Station. Two operating parameters determine the efficient operating of the unit, the desired dew point depression and the losses of TEG. This work presents an attempt to study the effect of all the operating variables on the efficiency of the dehydration unit such as: the effect of pressure and temperature of the natural gas has to be treated on the water content. Contactor pressure, TEG circulating rate and stripping gas flow rate are also considered in this study. The results showed that decreasing the temperature of the absorber from 130 F to 120 F will reduce the mass fraction of water in the dry gas stream from 0.000076 to 0.00002. Increasing the absorber pressure from 549.7 psia (design pressure) to 600 psia will also reduce the water content in the outlet dry gas from 0.000076 to 0.000022 as mass fraction. The simulation result shows linear relation between the wet gas flow rate from the regeneration column and the lean glycol flow rate.
A numerical model has been developed to determine the effect of the wire screen mesh (wick) type on the heat transfer performance of copper–water wicked heat pipe. This model represented as steady-state incompressible flow. The governing equations in cylindrical coordinates have been solved in vapor region, wick structure and wall region, using finite difference with forward-backward upwind scheme. The results show that increasing the mesh number led to decreasing the maximum heat transfer limit and increasing the capillary pressure. While, for the same heat input the operating temperature of the heat pipe increase when the mesh number increase. Also, it was found that increasing the evaporation length, with constant condensation length, decrease the operating temperature and increase the maximum heat transfer limit. For verification of the current model, the results of liquid pressure drop for a heat pipe have been compared with the previous study for the same problem and a good agreement has been achieved.
Recently, Internet of Thing technology has been used to develop numerous applications, this paper compromising design and implementation of greenhouse prototype that integrated with the IoT to adjust the system’s parameters and monitor the system status from any place in this world. This system involves three intelligent controllers that designed to stabilize the temperature degree, water level in soil, and light intensity inside the greenhouse prototype structure. These systems have been built by two important parts: the hardware and software. The hardware part could be achieved by designing and implementing the control circuits, actuators, and install the sensors as well as the devices. The second one is the software part which is involves implementing Fuzzy Inference Engine that represent the system’s brain that monitor and manage the entire process in the system to ensure the best performance. This system has been built to contain three control systems that means there are three different Fuzzy controllers. In order to keep the system practicality, the fuzzy controllers should be aggregated in single code that resides in single microcontroller chip with additional codes that perform the IoT duties. The proposed IoT system provides the ability for specific people to monitor and manage their systems remotely, using a web application with cloud technology. The major contributions of the proposed system are started by downloading the controller’s set-points (the desired environmental conditions) from the web page, transfer the set- points to the controllers, and upload data that read from sensors to the same web page.)
The solar chimney is a natural draft device that uses solar radiation to provide upward momentum to the in-flowing air, thereby converting the thermal energy into kinetic energy through an air turbine which in turn can be converted into electrical energy. The main parts of the solar chimney power plant are a large circular solar collector, a tall chimney, and an air turbine. In this paper, a theoretical study was performed to evaluate the performance of a solar chimney power plant system in Basrah City, where sunny days and solar radiation are high. A mathematical model was developed to study the effect of various parameters on the output power of the solar chimney. I1 was found that the output power depends strongly on the chimney tall and the difference between the collector air temperature and the ambient air temperature as well as the outside heat transfer coefficient, which essentially depends on the wind speed.
This study investigates the deep drawing process of carbon fiber-reinforced high-density polyethylene (CF-HDPE) composites through experimental and numerical approaches. The experimental part involved fabricating CF-HDPE sheets and conducting deep drawing operations under controlled parameters (punch speed, temperature, and forming depth) to evaluate material behavior and mechanical properties. Numerically, finite element analysis (FEA) using ABAQUS simulated the forming process, analyzing stress distribution, strain development, and material deformation under varying conditions. Results revealed that increasing forming depth and decreasing forming temperature elevated the required forming force. Comparisons between experimental and numerical outcomes showed consistent trends, though some differences arose due to factors like friction and material nonlinearity. The findings contribute to optimizing deep drawing processes for composite materials, enhancing manufacturing precision, and minimizing material defects.
Wastewater lagoons have proven to be an economically and environmentally beneficial alternative to traditional methods for treating sewage because of their unique properties, which include simplicity of use and inexpensive construction, energy, and maintenance costs. It is a natural wastewater treatment process that exploits the interactions between bacteria, algae, and other microorganisms and their surroundings to remove pathogens, organic matter, suspended particles, phosphates, ammonia, and nitrates. Stabilization lagoons are widely used throughout the world as they have proved to be a perfectly acceptable and satisfactory treatment system, the effluents produced in tertiary lagoons have been used for irrigation and aquaculture in many countries, indicating the high quality achieved during treatment in these units. This aim of this research is to overview the literature on lagoons' classification, design, and historical development. It also includes a set of relevant pilot and laboratory-scale experiments. As well as a comprehensive review of factors affecting lagoon performance, including sun's light, DO, pH, temperature, and nutrients. The relationship between these factors and their use in efficient contaminant removal is also discussed.
The aim of this paper is to reduce the corrosion rate by controlling the pH value, the polarization technique was used in this research in acidic, neutral and basic solutions. The corrosion rate was studied for carbon steel in filtered water, raw water and de-mineralized water under static condition at room temperature and 1 atm. Also, the effect of total dissolved solid (calcium, magnesium and sodium) on the corrosion rates was studies.
Evaporative cooling is a widely used energy-saving and environmentally friendly cooling technology. Evaporative cooling can be defined as a mass and heat transfer process in which the air is cooled by the evaporation of water and as a result a large amount of heat is transferred from the air to the water and thus the air temperature decreases. Evaporative cooling is mainly used in many cooling technologies used in buildings, factories, agricultural in addition to it is used industrially in cooling towers, evaporative condensers, humidification, and humidity control applications. Evaporative cooling is divided into direct evaporative cooling and indirect evaporative cooling, as well as water evaporative cooling and air evaporative cooling. This paper reviews the most important developments and technologies in evaporative cooling that lead to lower energy consumption and provide suitable cooling comfort.
Flaring systems used in oil production systems have a significant impact on both the economy and the environment as they discharge large quantities of burned gases of elevated temperature to the atmosphere that have the potential to be used in some applications. This study aims to investigate the economic losses incurred due to the combustion of gases not utilized in the Rumaila oil field in Basrah, the southern region of Iraq. Additionally, the potential to use flare gases for power generation and water desalination was studied. The mathematical models established by the U.S. Environmental Protection Agency (EPA) were utilized in this study to estimate and calculate the expected losses and used MatLab Ver. R22 to get result. The result leads to expected annular economic losses to reach $ 347,735,700. Also, the flare gases can be used to produce electric power of 1175 MW per year, it can be used for producing desalinating water of 115,911,900 m 3 for thermal desalination and 173,867,850 m 3 for membrane desalination.
In this study, a numerical investigation has been carried out for single phase flow behavior for thirty six internally finned tubes to demonstrate the effect of axial pitch to fin height ratio (p/e) for 0.8≤p/e≤6.345, helix angle of internal fins (β) for 30°≤β≤70°, apex angle of internal fins (α) for 0°≤α≤53.13°, internal fin height (e) for 0.6mm≤e≤1.0mm, internal tube diameter (di) with 14 mm and Reynolds number (Re) of single phase flow for 10000≤Re≤50000 on enhancement of forced convection heat transfer and reduction of friction factor by using ANSYS CFX program. It solves the three-dimensional Navier-Stokes equations for steady state turbulent with SST model and enhance wall treatment. The numerical analysis provided at fully developed velocity and temperature. Numerical results showed that the smallest axial pitch to fin height ratio (p/e) =0.8 and with apex angle α=10 degree provided enhancement of heat transfer of 2.8 to 3.55 times higher than of smooth tube. Finally, present numerical results are seen to be in good agreement with literature experimental correlations.
Castor Oil is a natural raw material, used to prepare Brominated Castor Oil (BCO) and quaternary ammonium salt based castor oil (TEt-CO). The two products were tested as demulsifiers and compared with a commercial demulsifier (Chimec2439) by using bottle test method. BCO showed a high ability on water separation efficiency 90% with a dose of 150µl at 120min time settling while TEt- CO showed a low water separation efficiency reached to 10%. The effect of the demulsifier BCO was tested by varying different variables which have an obvious effect on water separation efficiency such as: dose, temperature, time of mixing emulsion, pH and salinity of aqueous phase of emulsion, and water ratio. The effect of some additives (i.e. methanol, ethanol, xylene and toluene) on the efficiency of the BCO was tested for the purpose of enhancing its effectiveness to break the crude oil emulsion. The experimental data obtained by using BCO were formulated as a model using the Artificial Neural Networks (ANNs) to evaluating the water separation efficiency. Multi-layer perceptron artificial neural network was developed based on the collected data of this study. The results showed that the training algorithm of back propagation (BP) is sufficient enough in predicting BCO efficiency under different operation conditions. It was found that the correlation coefficient values are 0.9995 and 0.9999 for the testing and training data, respectively and the mean square error (MSE) was 6.18*10^-5 at 200 epochs.
The aim of this research is to predict the shrinkage defects in Al-Si castings by determination the suitable parameters and techniques which can be applied in casting simulation system. Also, it aims to specify the role of silicon content in amount, morphology, and distribution of these defects. The Numerical solution has been carried out using an explicit 3-D finite difference method for the given system of the casting and a mold. Additionally, an experimental casting of the studied samples was achieved. It was found that the shrinkage porosities increased with increasing the silicon content up to 7%, so at this peak, they spread in alt cast regions and cannot be predicted. The low silicon alloys suffered from only the shrinkage cavities defects that can be predicted by mapping the solidus time contours. Finally, it was concluded that the critical temperature gradient value of the porosities development in the eutectic (AI-12%Si) alloys was 1.3°C/cm.
In this work, the turbulent buoyancy driven fluid flow and heat transfer in a differentially heated tall rectangular enclosure filled with nanofluid is quantified numerically. The two dimensional governing differential equations (continuity, momentum, energy and low Reynolds number LRN k-ω turbulence equations) are discretized using the finite volume method. SIMPLE algorithm is employed to obtain stabilized solution for high Rayleigh numbers. Two types of nanofluids namely, Al2O3-water and Cu-water, were considered. The effect of Rayleigh number (1010 to 1012), diameter of nanoparticles in the range 25-100 nm, nanoparticle volume fraction in range 0-0.08 and the aspect ratio (30, 40 and 50) on fluid flow and heat transfer are investigated. The present results are compared with previously published work and a qualitative agreement with good validation is obtained. Results show that addition of nanoparticles makes the liquid be more viscous which decreases the vertical velocity component and also decreases the temperature gradient near the walls. Also an announced heat transfer enhancement is obtained with nanoparticle volume fraction reaching a maximum point called optimal volume loading, at which the maximum convective heat transfer is obtained, and then it decreased with further increase of volume fraction.
This paper deals with the behavior of reinforced concrete anchor blocks for underground steel pipelines.~ under the effect of loads caused by internal pressure and temperature variation due to the transportation of hydrocarbon products. The finite element method is used to carry out the analysis using the ANSYS 5.4 program. To study the effect of oil, it is represented by springs with different values for the modulus of subgrade reaction in normal and tangential reactions. It is concluded that increasing the values of the modulus of subgrade reactions, kn and ks of the soil surrounding the reinforced concrete anchor block causes an increase in the failure loads of the block. But at high values of these modules, the rate of this increase in the failure load will decrease. The area of the passive face of the concrete anchor block is found to have the main effect on the failure load as compared to the length of that block. The failure load of the concrete anchor blocks that have square cross sections is 1.33 times larger compared to that of rectangular sections. It is also concluded that locating the steel flange at the middle of the block leads to a larger resistance of anchor blocks as compared to any other position.
Zinc and its alloy coatings are commonly used to provide cathodic protection for weathering steel. However, the steel substrate corrodes faster than the Zinc coating because of the coating's negative corrosion potential. Many studies have examined Zinc and alloy coatings' resistance to corrosion. Hot-dip galvanizing, Electrodeposition, and Zinc-rich coat (ZRC) spray are just some of the methods that can be used to deposit such coatings. Commercially available 99.95 % pure Zinc oxide was used in the electroplating process in this investigation. Steel samples were plated in Zinc sulphate and Zinc oxide solutions and were controlled by different bath parameters such as voltage, current, pH, temperature, and coating time. The addition of hexagonal Boron Nitride (h-BN) nanoparticles has also shown significant improvements in corrosion resistance. However, Zinc-based coating techniques reinforced with h-BN incorporation show the best corrosion current density ( I corr ) of Hot dip 2 % wt. (2.1 µA/cm 2 ), ZRC 2.5 % wt., (4.4 µA/cm 2 ), and electroplating 15.75 g/L (0.081 µA/cm 2 ), which is an order of magnitude lower than coatings without h-BNs. The corrosion rates and current densities of Zn/h-BN coated layers were investigated in a controlled laboratory environment that mimicked natural conditions (Rainwater solution) by extrapolating polarization curves.
Fluidized bed reactor (FBR) is an attached growth system used mainly for biological treatment of industrial wastewater of high organic content. These wastewaters are usually resulted from refineries and milk, starch, and olive oil industries. The objective of this study is to investigate the use of fluidized bed reactor for treating sanitary sewage. The study was accomplished using a pilot plant of the FBR. The pilot plant was constructed and installed in Hamdan Sewage Treatment Plant in Basrah governorate. That was to maintain continuous source of settled sewage which is the influent to the FBR. The period of plant operation was nine weeks. During, this period, the plant was operated at three phases of different conditions (up flow velocity and recirculation ratio). To study the performance of FBR, the main measured parameters were; BOD, DO, VSS, pH, and temperature. The most important conclusions of this study are; (1) the maximum efficiency of BOD removal is 78.6% which was obtained for hydraulic retention time (HRT) of 24min and upflow velocity of 1.59m/min, (2) the effluent BOD values during phases-1 and 2 of plant operation match that of stabilization ponds and trickling filters and during phase-3 matches that activated sludge process, (3) during all operation phases, the values of effluent pH are within the limits specified in national standards of secondary effluents, (4) as F/M increases, the efficiency of BOD removal decreases and the maximum efficiency of BOD removal (78.6%) was obtained at F/M ratio equals 23.47 day -1 , and (5) the HRT of fluidized bed reactor is on order of minutes, while, the values of HRT of activated sludge systems and stabilization ponds are on order of hours and days, respectively.
The Atmospheric Water Generator (AWG) is an environmental water recovery that easily dehumidifies water vapor moisture from the air. This article presents an experiment to construct an AWG model using solar energy as a source of power. An experimental and numerical study for a device of (AWG) is performed. The experimental work is performed at Basrah city, located in the south of Iraq, during August and September of 2019 and March of 2020. The theoretical results are calculated by EES and the numerical study has been conducted by the (ANSYS19/CFD/ FLUENT) program. The experimental device is tested for different days with different climate conditions. The Maximum water production obtained is 3.4 L/day from all the testing days, for different hours of operation when the relative humidity in the range of (45 – 95 %) and the temperature range from 17 °C to 45 °C. The results shown that, the water production rate is increased with increasing humidity, temperatures, hours of operation, and model size.
This review focuses on the experimental and numerical studies of sweeping impingement jets that serve in cooling of hot surfaces. It is known that the impinging jets produce high-localized heat transfer coefficient. The sweeping jet covers a wider area on a hot target to improve the heat transfer rate, they could be used to increase the cooling rate of the impingement surface by disturbing the boundary layer. To display a readable survey, the current review was partitioned to four groups based on engineering configurations. The review shows that the sweeping nozzle gives better efficiency in heat transfer, improved Nusselt number and uniform target surface temperature, compared with the conventional normal jets. The current review reveals that the sweeping-jet mechanism can be achieved either by fluidic oscillator or by exciting a flexible wall forming an oscillating jet. Most of the fluidic oscillator researches are conducted experimentally (27%), while the researches that use flexible wall are about 24%.
The present study aims to investigate the influence of heat treatment and surface finish on the behavior of crevice corrosion resistance of AISI 410 and 416 martensitic stainless steels thus, to quantify the conditions at which crevice corrosion minimize as possible. The experimental work carried out during this study involves material selection, chemical composition tests, specimens preparation before heat treatments, austenitizing at temperature range (925-1010˚C) and for holding time periods of (30, 45 and 90 min), air and oil quenching followed by tempering at heating range of (205- 605 ̊C) and for 45 min, micro hardness tests, specimens grinding, surface roughness measurements, crevice corrosion tests, crevice evaluation and microstructure tests. Theoretically, empirical equations for crevice maximum depth under the effect of surface roughness and hardness for both AISI 410 and 416 steels were determined. While for microstructure analysis, carbides average area was determined by using the ImageJ analysis program and a mathematical model was also predicted. Results showed that, as hardness and surface roughness increase crevice corrosion resistance decreases. Therefore, material treated by annealing can minimize crevice corrosion rates more than that treated with hardening.
A numerical study of mixed convection inside a horizontal channel with an open square cavity that includes an adiabatic rotating cylinder. The bottom wall of the cavity is heated at a constant temperature, and the remaining walls are adiabatic. The flow is incompressible, laminar and steady state. The equations of continuity, momentum and energy are solved numerically using computational fluid dynamics (CFD) with the commercial software package FLUENT 2019 R1. Reynolds number values of 50, 100 and 150, the Richardson number (0.1 ≤ Ri ≤ 10) and the angular velocity ( ω ) of cylinder is (0.5 ≤ ω ≤ 4) rad/sec with direction counter clockwise. Prandtl number for air flow is ( Pr = 0.7). The results are presented in terms of streamlines, isotherms, and the average Nusselt value is given over the heated bottom cavity. The combined effects of natural and forced convection in and out of the cavity were obtained. The results showed that at low Richardson values, Ri = 0.1 the effect of buoyancy force is neglected. The effect of increasing the cylinder speed is clearly noticeable at low Reynolds values, Re = 50. Average Nusselt values increase with increasing rotational speed of the cylinder for all Richardson values.
In this study, a numerical investigation has been carried out for single phase flow behavior for thirty six internally finned tubes to demonstrate the effect of axial pitch to fin height ratio (p/e) for 0.8≤p/e≤6.345, helix angle of internal fins (β) for 30°≤β≤70°, apex angle of internal fins (α) for 0°≤α≤53.13°, internal fin height (e) for 0.6mm≤e≤1.0mm, internal tube diameter (di) with 14 mm and Reynolds number (Re) of single phase flow for 10000≤Re≤50000 on enhancement of forced convection heat transfer and reduction of friction factor by using ANSYS CFX program. It solves the three- dimensional Navier-Stokes equations for steady state turbulent with SST model and enhance wall treatment. The numerical analysis provided at fully developed velocity and temperature. Numerical results showed that the smallest axial pitch to fin height ratio (p/e) =0.8 and with apex angle α=10 degree provided enhancement of heat transfer of 2.8 to 3.55 times higher than of smooth tube. Finally, present numerical results are seen to be in good agreement with literature experimental correlations.
Nanoparticles show mechanical, electrical, chemical and optical properties that are different and superior to bulk materials. In the present work, α-Alumina nanoparticles were synthesized using the nonorganic Sol-Gel method under controlled conditions. Because of the low cost of its raw materials, low manufacturing temperature and the high purity of the product, Sol-Gel method is the best in the manufacture of nanostructures like metal oxide nanoparticles. The precursor of the Sol-Gel process was aluminum nitrate with ethanol. The prepared nanopowder was evaluated by X-ray diffraction (XRD), scanning electron microscope (SEM), electron dispersive spectroscope (EDS) and Malvern Zetasize analyzer.
The effect of thermal aging on the tensile properties of cast stainless steel during service in light water reactors has been evaluated and recorded by the Argonne National Laboratory. Tensile data for several experimental and commercial heats of cast stainless steel (CF-8M) are presented for predicting the change in tensile flow and yield stresses and engineering stress-strain curve as a function of time and temperature of service in the light water reactors using Neural Networks. Thermal aging increases the tensile strength of this type of steel. The result and correlation described by this work may be used for assessing thermal embitterment of cast stainless steel components.
In this study, a numerical investigation has been carried out for single phase flow behavior for thirty six internally finned tubes to demonstrate the effect of axial pitch to fin height ratio (p/e) for 0.8≤p/e≤6.345, helix angle of internal fins (β) for 30°≤β≤70°, apex angle of internal fins (α) for 0°≤α≤53.13°, internal fin height (e) for 0.6mm≤e≤1.0mm, internal tube diameter (di) with 14 mm and Reynolds number (Re) of single phase flow for 10000≤Re≤50000 on enhancement of forced convection heat transfer and reduction of friction factor by using ANSYS CFX program. It solves the three- dimensional Navier-Stokes equations for steady state turbulent with SST model and enhance wall treatment. The numerical analysis provided at fully developed velocity and temperature. Numerical results showed that the smallest axial pitch to fin height ratio (p/e) =0.8 and with apex angle α=10 degree provided enhancement of heat transfer of 2.8 to 3.55 times higher than of smooth tube. Finally, present numerical results are seen to be in good agreement with literature experimental correlations.
The aim of this study is to investigate the effect of heat treatments on the impact properties of hot rolled high strength steel and describes the effect of tempering temperature and quenching media on the microstructure, hardness, and impact resistance of plates. In the present study a high strength steel was austenitized at 900 °C with different quenching medium and followed by tempering at 300 °C, 500 °C. After thermal treatments, the values of Charpy impact resistance, hardness, and microscopic structure were evaluated from mechanical and metallographic analysis of metals respectively. The change of mechanical properties and microstructure of the metal with the existence of heat treatment with the ballistic performance of high-strength steel. Experimental results showed that tempering at 500 °C for 2 hours after water quenching medium it provides the best mechanical properties in conjunct on with an improved in microstructure.
Over the past years, researchers have been focusing on development the robotics and actuation due to increase demand for these applications like industrial engineering, oil industry, healthcare, aerospace … etc. This work involves the design, construction and control of the Shape Memory Alloy (SMA) actuator. The industrial actuator has many characteristics able to be measured, which have an impact on the efficiency and effectiveness of the actuator while the execution of its tasks. The most important measurable characteristics are repeatability and accuracy. The current system typically is using Nitinol (Nickle Titanium Naval Ordinance Lab), which is one of the Shape Memory Alloy that contract when applying specific heat on it, and it can be used as an actuator. This work presents SMA in the shape of a spring to operate and control the accurate position of the 2-D system which containing four SMA springs, two SMA springs for the x -axis and two SMA springs for the y - axis. The theoretical design and calculations for SMA springs have been presented to collect information about the SMA springs. In a practical manner, the SMA spring characteristic like force and displacement were collected by a test bed that was designed and constructs before making the final rig. The setting shape of the SMA spring was presented and done as per the theoretical calculations. In the rig, each axis works as a two-direction actuator, the actuator is not prone to precise position points due to hysteresis and temperature variation. The SMA spring exhibited hysteresis and imprecise pointing, for that employing PID (Proportional Integral Derivative) with tracking mode controller to compensate the hysteresis. PID control system is played a decisive role with tracking mode model that achieves the aim behind the construction of the experimental rig. Good results have been obtained presented in three cases of drawing different shapes.
The effect of different dosages of the high range water reducing admixture–additive- (HRWRA), the commercially polymeric material (Plastocrete-N), on the corrosion resistance of embedded steel in concrete exposed to chloride solution in the absence and presence of sulfate ions was studied. In the present study, four levels of polymeric material (Plastocrete-N) (0.125%, 0.250%, 0.375%, and 0.500% by weight of cement) were used to prepare HRWRA treated concrete. The concrete specimens exposed to chloride and chloride–sulfate solutions at concentrations of (3.5% NaCl and 5% Na2SO4), at ambient temperature. The electrochemical behavior of steel in both reference and HRWRA concretes was studied under the effect of corrosive environments using corrosion measurement systems such as: a) half – cell potentials measurement system and b) accelerated corrosion test system. The results showed that a longer time of corrosion initiation (180 day) observed with 0.500% HRWRA containing concrete compared to other different HRWRA percentage including the reference concrete. It was concluded that the use of 0.500% HRWRA provided superior protection to steel reinforcement in concrete that subjected to corrosive environments. Furthermore, the steel with 0.500% HRWRA was subjected to corrosion test by mass loss, it is evident that a reduction in mass loss by about 90.2% and 85.2% in both solutions, respectively.
Four groups of AISI 1020 specimens were heat-treated at 850 °C in a muffle furnace for 30 minutes then quenched in oil. The samples were tempered at 400 °C with a time period for each group as (group B, 2 hours), (group C, 3 hours), and (group D, 4 hours). The mechanical properties of the samples were studied using universal tensile testing equipment and a Brinell hardness testing machine. The hardness values of the quenched samples were calculated from a given modified equation. The torsional fatigue behavior of AISI 1020 was discovered in this investigation for heat-treated specimens and compared with the original specimens. All groups were subjected to an analysis using an optical microscope. Pearlite is formed when is heated in the austenitic region and then cooled below a lower critical temperature. It was concluded that the heat treatment increases the hardness for the specimens while decreased the shear fatigue ductility coefficient. Also, the heat treatment increased the shear fatigue strength coefficient. Furthermore, increasing in the time period of the tempering process was leaded to decrease the coefficient of shear fatigue strength and increased the coefficient of shear fatigue ductility.
This study investigates the effect of rotating two rows of horizontal cylinders on forced convection heat transfer in cross flow. Each row consists a three rotating horizontal cylinders heated at constant temperature. The governing equations for the steady, laminar, two dimensional, incompressible flow and constant fluid properties are solved numerically using the finite element method with FlexPDE soft package for a two rows of rotating cylinders at the same direction and at opposite directions. The main parameters are: Reynolds number ( 40 10 Re − = ), Prandtl number ( 7.0 Pr = ), dimensionless longitudinal pitch (SL=1.5-2.5), dimensionless transverse pitch (ST=1.5-2.5) and the dimensionless angular velocity (Ω=0-3) (for both directions clockwise CW and counter clockwise CCW). It is found that the average Nusselt number increased with increasing Re and ST, and decreases with Ω and SL. The results are compared with other authors and give a agreement.
This paper aims to investigate the effect of Ag nanoparticles addition in different percentages (0.12 wt. %, 0.15 wt. %, 0.25 wt. %, 0.35 wt. %) on the microstructure properties of Cu-21%Zn-6%Al shape memory alloy. Optical and SEM were carried out to studied such effects. Two heat treatments were carried out at (825 ℃ and 850 ℃) for 10 min and quenched in ice water. It was observed that both of heat treatment lead to formation M18R martensite with V-shape and needle like, but raising the temperature of heat treatment from 825 ℃ to 850 ℃ lead to a decrease formation α phase, which leads to improving the shape memory properties. Refinement of the grain size resulted as Ag nanoparticles addition increased from 0 to 0.25 wt. %, the grain size decreases from 1551 μm to 212 μm with reduction of 86.32 wt. % at 0.25 wt. % Ag. The microstructure observation indicated that the Ag nanoparticles addition leads to creating a multi-variant oriented martensite microstructure after quenching process in ice water.
The electronic equipment industry has developed rapidly in recent years. The amount of heat emitted from such equipment is seriously increased. Increasing the temperature of the electronic devices degrades their performance and as a final result their failure. Therefore, the requirements for an effective cooling system have become more important than ever. One of the most important methods of heat dissipation that the researchers focused on is the use of piezoelectric fans (PE). The current study reviews most of the developments that have taken place since its discovery nearly 40 years ago and focused on reducing power consumption. Most of the improvements and developments have been focused on obtaining optimal designs for these piezoelectric fans, which are used in different applications. This review clarifies the foundations and concepts of designing piezoelectric fans by comparing the data presented in previous studies. Furthermore, in the last ten years, numerical simulation has entered as an effective tool in predicting the optimal design of piezoelectric fans. The design of piezoelectric fans is in two forms, either single or multiple. The single fan system is used within a limited range of applications, as large cooling systems cannot be replaced by it. Therefore, the cooling system consisting of multiple piezoelectric fans is promising as a unique solution to effectively dissipate heat in electronic devices. The percentage of experimental studies is about 32 % while the studies of CFD is about 21 %, and the combined one is about 47 %.
The dieless drawing process is an innovative method emanated and appeared in coincidence with development of the concept of metal superplasticity. It is utilized from the local heating of a wire or tube to a specified temperature and followed by a local cooling, so an additional deformation is inhibited. In this study, a special dieless drawing machine was designed to carry out an experimental program on SUS304-stainless steel wire having diameter of (1.6-2) mm to investigate the main process parameters such as speeds, heat quantity, heating coil width and heating-cooling separation distance. Also, a numerical model based on thermo-mechanical analysis was developed and validated with experimental program. Furthermore, an artificial neural network ANN model based on current experimental data was prepared to predict the dieless drawing behavior. A maximum area reduction of 40.7% was obtained in single pass. A 3.12mm/s feeding velocity and 4.97mm/s drawing velocity were realized through the experimental tests. The results showed that both drawing force and wire profile were effected by increasing of feeding speed, heating coil width and separation distance. Also, it is confirmed that strain rate was reduced by increasing the heating coil width and the reduction ratio was promoted. A maximum error of 21% was recorded between ANN model and experimental results. The results showed a good agreement among experimental, numerical and ANN models.
The thermal performance of an absorption refrigeration system powered by solar pond heat was studied, simulated, and evaluated under the climatic conditions of Basra, Iraq. The simulation used MATLAB to solve the heat and mass transfer equations within the three layers of the solar pond (assuming NaCl as the salinity gradient medium) and linked them via a heat exchanger to the absorption refrigeration system to determine the temperatures supplied to the absorption cycle. The absorption cooling system operates on a lithium bromide-water pair and contains an internal heat exchanger between the generator and absorber with an assumed efficiency of 80%. The simulation was conducted over several months of the year, from March to October, and daily climatic variables such as solar radiation and ambient temperature specific to Basra were considered, allowing the system's performance to be evaluated under realistic climatic conditions. The objective was to evaluate the coefficient of performance (COP) of absorption refrigeration systems and demonstrate the feasibility of using solar ponds as a sustainable heat source for cooling in hot regions. The study demonstrated the feasibility of operating an absorption refrigeration system using the thermal energy stored in the lower layer of the solar pond, while maintaining good thermal stability in that layer throughout the day, especially in areas with high solar radiation, such as Basra. The simulation model was developed entirely in MATLAB using fundamental physical equations that describe each component of the solar pond and absorption refrigeration system, without relying on pre-existing components or tables. This provides greater modeling flexibility and a deeper understanding of system behavior under hot climate conditions.
A proper ventilation offered warranty for a perfect indoor environment. Indoor air environment includes indoor thermal environment and indoor air quality (IAQ). In this paper a numerical investigation of the indoor environment in different ventilations was accomplished. The Cardiac Care Unit (CCU) in Al-Rifai hospital in Thi-Qar governorate was chosen to be investigated, and its thermal achievement and indoor air quality in the hot summer weather were simulated. For the numerical study, the fluent technique used to set up the physical and numerical model of CCU. An attention has been paid carefully to considerate the distributions of the temperature and the velocity fields, followed by an argument of two different ventilation patterns; up-in and up-out ventilation (UV) and displacement ventilation (DV). After making the comparison, it was noticed that the displacement ventilation (DV) is clearly super than that of the up-in and up-out ventilation (UV) due to improvement in the indoor air quality.
This article provides an overview of the studies that have been conducted on the characteristics of epoxy resins containing various types of silica nanoparticles and microparticles, as well as their performance in the industrial application of functionally graded materials (FGMs). Silica nanoparticles and microparticles are used to create epoxy resins in order to improve various properties, such as thermal stability, adhesiveness, electrical conductivity, strength, modulus, and toughness. This review examines the literature that has been published in the last decade, compares the results, focuses on the mechanical and thermal properties, and discusses the changes that have resulted in improvements in those properties. Previous experimental findings are presented and contrasted to demonstrate the extent to which silica filler content contributes to improving the properties of composite materials. The findings reveal that the characteristics of epoxy compounds can be improved by adding a particular amount of silica particles. There is a correlation between an increase in the silica amount and an increase in the Young modulus of epoxy compounds, this correlation becomes stronger as the silica amount increases. Additionally, the tensile strength of epoxy compounds increases to a certain limit as the amount of silica nanoparticles increases. In contrast, the hardness of the material increases as the silica amount increases. The density of the material also increases steadily as the silica amount in the material increases. According to thermal analysis results from calorimetric research on epoxy–silica systems, the glass transition temperature increases as the silica amount increases.
The effect of fouling due to scale formation of pre-heater tubes on the thermal performance of Reticulating multi stage flash Distillation plant performance ratio and the increase of the ratio of Makeup water to the product Quantity for a 5MGPD recirculating System has been prediction The results appeared That eth Effect of scale formation is more Effected as the Maximum brine temperature decrease.
Human beings are facing an unprecedented rise in temperature rates not recorded for years. HVAC (heating, ventilation, and air conditioning) systems have been created and enhanced to solve this issue. Cooling load must be estimated with accepted methodologies before designing an efficient and effective air conditioning system. Companies, researchers, institutions, and others advise and develop many cooling load calculation methods. Each one of these methods has its advantages and disadvantages and may give a slightly different result for the same case. For each building, whether it was residential or commercial buildings, gyms, or shopping malls, before making the decision on (HVAC) systems to be used, both heating and cooling loads should be obtained as correctly as possible to minimize expenses as possible. Since the HVAC system consumes the most energy in an air-conditioned building, an accurate method of cooling load estimation is necessary. Consequently, an energy-efficient air conditioning system reduces greenhouse gas emissions into the atmosphere while also saving money on electricity. Two cases have been compared and studied, one in Dubai UAE, and the other in Baghdad Iraq. Three different methods, HAP, hand calculation method (CLTD/SCL/CLF), and MS-EXCEL E20 form sheet were used to compare the accuracy of the results for cooling load. Results of E20 and HAP are very close to each other with high accuracy for peak load, the big difference can be found between the CLTD method and the other two methods. The value of the maximum difference percentage was found between CLTD and E20 equals 3.28% and 7.96%, on the other hand, the lowest difference was equals to 0.3% and 1.51% between HAP and E20 results for Baghdad and Dubai respectively. Traditional and local materials came from local factories, used in buildings played a big effect on the results, which may not match those materials stated in the ASHRAE or CARRIER tables, which need to be considered in the results and calculation procedure. However, all methods have a percentage of difference but all results are within the accepted range and are applicable for practical cases. Of course, this percentage is minimal with some methods and maximum with others.
Flocculation process is used to agglomerate colloids to form large and heavy flocs. It is accomplished using mechanical or hydraulic slow mixing. The hydraulic mixing is usually achieved using baffles. The aim of this study is to conduct experimental work to study the effect of baffles shape and configuration on baffled flocculator performance. The work includes 304 experiments conducted in a pilot plant of baffled flocculator. Two arrangements of three baffle shapes (blind baffles, baffles of rectangular slot and baffles of circular slots) were adopted. During each experiment, water turbidity and temperature, influent flow rate and head loss were measured. The main outcomes of this study are; (1) for all baffle types and arrangements, flocculation efficiency (FE) increases with the increase of velocity gradient (G) till it reaches a maximum value, then, it decreases and the G value which produces the maximum FE varies with detention time (t), (2) within the applied range of Gt values (10231-25304), the correlation between FE and Gt is weak to moderate positive and varied according to baffles type and arrangement, (3) within the applied range of initial water turbidity (IWT) values (18.1-196) NTU, the correlation between FE and IWT is weak positive to good positive represented by logarithmic relationship, and (4) within the implemented baffle types, the blind baffles type gives the highest FE values for all the baffles number as compared with the other baffle types. Also, the most frequent head loss coefficient values were obtained.
Shatt Al-Arab river has been used as the raw material for the drinking water, irrigation and fish purposes in Basrah city. Concurrently, this river has been polluted by domestic, farming and industrial waste. Three main factories lie on the bank of Shatt Al-Arab river: Al-Hartha Paper Mill, Hartha Power Station and Al-Najibia Power Plant. All these consume water from the river and return their wastewater back to it. The aim of this study is to assess the water quality of Shatt Al-Arab river and its suitability for drinking, irrigation and aquatic life through physicochemical analysis temperature, pH, EC, Total Dissolve Solid (TDS), Cl − , Na + , K + , Ca +2 , Mg+2, HCO 3 total hardness, Biological Oxygen Demand (BOD5), Dissolved Oxygen (DO), Chemical Oxygen Demand (COD). BOD5 concentration near factories showed polluted water, unsafe and requiring costly treatment to use for drinking water. Sodium concentration is a key factor for irrigation, which represent by SAR and SSP. As SSP exceed 75.73 % in water near these factories, this could breakdown soil structure and can damage agriculture area. The high concentrations of BOD5 and COD could pose a threat to aquatic life and fishes. As Shatt Al-Arab river is used for different purpose, the result in this study showed polluted water near industrial areas. Therefore, it is recommended to have regular data on water quality for this river near these areas.
Numerical analysis of transient laminar three- dimensional buoyancy-driven convection in an inclined three- dimensional trapezoidal air-filled enclosure was investigated in this paper. The right and left sidewalls of the enclosure are kept at constant cold temperatures. The bottom wall is maintained at a constant hot temperature , while the top wall is considered adiabatic. Numerical investigation is performed for Rayleigh numbers varied as 10 3 ≤ Ra ≤ 10 5 , while the trapezoidal enclosure inclination angle is varied as 0° ≤ ≤ 180°. Prandtl number is considered constant at Pr = 0.71. Flow and thermal fields are presented in both two and three- dimensional pattern. Also, both local and average Nusselt numbers are calculated and discussed. The results show that when the Rayleigh number increases, the flow patterns are changed especially in three-dimensional results and the flow circulation increases. The minimum average Nusselt number inside the trapezoidal cavity corresponds to the highest 180 ].While, the average Nusselt inclination angle [i.e., 30 . Moreover, number reaches its maximum value at when the Rayleigh number increases the average Nusselt number increases as expected.
The direct-contact evaporation method is characterized by its effectiveness in applications of heat exchangers, especially in cooling systems, due to the absence of any heat resistors that prevent the transfer of heat between the cold and hot medium. The direct contact heat transfer depends mainly on how quickly the heat is taken by the bubbles of the evaporative refrigerant from the liquid and the increase in its volume up to the top of the heat exchanger, which is usually a cylindrical liquid column so that the temperature drop therein is uniform and even. There is much research on the method of heat transfer by direct contact. In this research, we collected and summarized most of the theoretical and practical researches that examined this method with the most important findings.
The analysis of raw domestic sewage has a greater importance for design of an effective and economic rational sewage treatment. The objectives of this study are to determine the chemical, physical and Biochemical characteristics of raw domestic sewage for Basrah city. Results show that; the strength of Basrah raw domestic sewage can be classified as a strong strength concentration wastewater due to high levels of organic loading rate BOD5 , COD. Also, it can be seen a very high concentrations of TDS , CL- and increasing in EC levels above the typical limits due to the salinity of domestic water supply in Basrah. High concentrations of oil and grease were found as result of misuse of the sewerage system. While the values of pH, temperature, nutrients and the number of FC are within the typical acceptable limits.