Cover
Vol. 23 No. 2 (2023)

Published: December 31, 2023

Pages: 78-86

Review Article

A Review Study of Sweeping and Normal Impingement Jets

Ahlam A. Hassan 1 Muneer A. Ismael 1
1 Department of Mechanical Engineering, College of Engineering, University of Basrah, Basrah, Iraq
History
  • Received: April 6, 2023
  • Revised: May 2, 2023
  • Accepted: May 6, 2023
  • Available Online: December 30, 2023
DOI

https://doi.org/10.33971/bjes.23.2.10

Abstract

This review focuses on the experimental and numerical studies of sweeping impingement jets that serve in cooling of hot surfaces. It is known that the impinging jets produce high-localized heat transfer coefficient. The sweeping jet covers a wider area on a hot target to improve the heat transfer rate, they could be used to increase the cooling rate of the impingement surface by disturbing the boundary layer. To display a readable survey, the current review was partitioned to four groups based on engineering configurations. The review shows that the sweeping nozzle gives better efficiency in heat transfer, improved Nusselt number and uniform target surface temperature, compared with the conventional normal jets. The current review reveals that the sweeping-jet mechanism can be achieved either by fluidic oscillator or by exciting a flexible wall forming an oscillating jet. Most of the fluidic oscillator researches are conducted experimentally (27%), while the researches that use flexible wall are about 24%.

Keywords

References

  1. R. K. Lundgreen, M. A. Hossain, R. Prenter, J. P. Bons, J. Gregory, and A. Amer " Impingement Heat Transfer Characteristics of a Sweeping Jet" American Institute of Aeronautics and Astronautics, /DOI:10.2514/6.2017-1535 https://arc.aiaa.org
  2. M. A. Hossain, R. Prenter, R. K. Lundgreen, L. M. Agricola, A. Ameri, J. W. Gregory, J. P. Bons " Investigation of Crossflow Interaction of an Oscillating Jet", American Institute of Aeronautics and Astronautics, 10.2514/6.20171690. https://www.researchgate.net/publication/31211037
  3. X. Wen, Y. Liu, and H. Tang," Unsteady Behavior of a Sweeping Impinging Jet: Time-Resolved Particle Image Velocimetry Measurements", Experimental Thermal and Fluid Science96 (2018) 111127. https://doi.org/10.1016/j.expthermflusci.2018.02.033
  4. X. Wen, Y. Liu ""Lagrangian Analysis of Sweeping Jets Measured by Time-Resolved Particle Image Velocimetry", Experimental Thermal and Fluid Science, 97 (2018) 192204. https://doi.org/10.1016/j.expthermflusci.2018.04 .
  5. X. Wen, Z. Li, W. Zhou, and Y. Liu1," Interaction of Dual Sweeping Impinging Jets at Different Reynolds Numbers", the American Institute of Physics, Physics of Fluids 30, 105105 (2018); doi: 10.1063/1.5054161.
  6. D. Kim, S. Jeong, T. Park, and D. Kim," Impinging Sweeping Jet and Convective Heat Transfer on Curved Surfaces", International Journal of Heat and Fluid Flow, 79 (2019) .
  7. S. Kim, H. Kim, and K. Kim, "Measurement of TwoDimensional Heat Transfer and Flow Characteristics of an Impinging Sweeping Jet", International Journal of Heat and Mass Transfer 136 (2019).415-426.
  8. W. Zhou, L. Yuan, Y. Liu, Di Peng, and X. Wen, "Heat Transfer of a Sweeping Jet Impinging at Narrow Spacings", Experimental Thermal and Fluid Science 103, (2019).89-98.
  9. M. Kim, D. Kim, E. Yeom, and K. Kim," Experimental Study on Heat Transfer and Flow Structures of FeedbackFree Sweeping Jet Impinging on a Flat Surface", International Journal of Heat and Mass Transfer 159 (2020) 120085.
  10. M. Hossain, A. Ameri, J. Gregory, and J. Bons, "Effects of Fluidic Oscillator Nozzle Angle on the Flow field and Impingement Heat Transfer”, AIAA Journal April (2021), DOI: 10.2514/1.J059931
  11. C. Camci and F. Herr, "Forced Convection Heat Transfer Enhancement Using a Self-Oscillating Impinging Planar Jet" Transactions of the ASME 770 Õ Vol. 124, (2002).DOI: 10.1115/1.1471521. http://heattransfer.asmedigitalcollection.asme.org
  12. A. Eghtesad, M. Abad bozchelou, and H. Afshin," Heat Transfer Optimization of Twin Turbulent Sweeping Impinging Jets", International Journal of Thermal Sciences 146 (2019) 106064.
  13. B. N. Hewakandamby," A Numerical Study of Heat Transfer Performance of Oscillatory Impinging Jets", International Journal of Heat and Mass Transfer 52 (2009) 396–406 [email protected]
  14. M. Herrada, C. Pino, and J. Casanova, " Confined Swirling Jet Impingement on a Flat Plate at Moderate Reynolds Numbers”, American Institute of Physics of Fluids 21, 013601 (2009). DOI:10.1063/1.3063111. http://ojps.aip.org/phf/phfcr.jsp
  15. K. Ichimiya and K. Tsukamoto," Heat Transfer Characteristics of a Swirling Laminar Impinging Jet", Journal of Heat Transfer, Vol. 132 / 012201-1 (2010). http://heattransfer.asmedigitalcollection.asme.org
  16. K. Brown, G.Byrne, T. Donovan and D. B. Murray," Effect of Thermal Boundary Condition on Heat Dissipation due to Swirling Jet Impingement on a Heated Plate", Journal of Physics: Conference Series 395 (2012) 012039, doi:10.1088/1742-6596/395/1/012039. ( http://iopscience.iop.org/17426596/395/1/012039 )
  17. Z. Lin, Y. Chou, and Y. Hung, "Heat Transfer Behaviors of a Confined Slot Jet Impingement”, Int. J. Heat Mass Transfer. Vol. 40, No. 5, pp. 1095-1107, (1997).
  18. M. Rady, and E. Arquis, "Heat Transfer Enhancement of Multiple Impinging Slot Jets with Symmetric Exhaust Ports and Confinement Surface Protrusions" Applied Thermal Engineering 26,1310–1319 (2006). www.elsevier.com/locate/apthermeng
  19. A. Sivasamy, V. Selladurai, and P. Rajesh Kanna," Numerical Simulation of Two-Dimensional Laminar SlotJet Impingement Flow Confined by a Parallel Wall", International Journal for Numerical Method in Fluids, 2007 55:965–983, DOI: 10.1002/fld.1492. [email protected]
  20. E. Arquis, M. Rady, and S. Nada," A Numerical Investigation and Parametric Study of Cooling an Array of Multiple Protruding Heat Sources by a Laminar Slot Air Jet "International Journal of Heat and Fluid Flow 28, 787– 805, (2007) 787-805 www.elsevier.com/locate/ijhf
  21. M. Sharif, and A. Banerjee, "Numerical analysis of heat transfer due to confined slot-jet impingement on a moving plate" Applied Thermal Engineering 29, 532–540, (2009)) 532–540.
  22. D. Lee, J. Bae, M. Ryu, and P. Ligrani, "Confined, Milli scale Unsteady Laminar Impinging Slot Jets: Effects of Slot Width on Surface Stagnation Point Nusselt Numbers " Journal of Electronic Packaging, Vol. 134 / 041004-1, December (2012) DOI: 10.1115/1.4007317 http://www.asme.org/about-asme/terms-of-use
  23. C. Agrawal, R. Kumar, A. Gupta, and B. Chatterjee, " Rewetting and maximum surface heat flux during quenching of hot surface by round water jet impingement" International Journal of Heat and Mass Transfer, Volume 55, May (2012). http://dx.doi.org/10.1016/j.ijheatmasstransfer.2012.04.045
  24. M. Zukowski," Heat Transfer Performance of a Confined Single Slot Jet of Air Impinging on a Flat Surface" International Journal of Heat and Mass Transfer, Volume 57, Issue 2, February (2013). http://dx.doi.org/10.1016/j.ijheatmasstransfer.2012.10.069
  25. S. Caliskan, S. Baskaya, and T. Calisir, "Experimental and Numerical Investigation of Geometry Effects on Multiple Impinging Air Jets" International Journal of Heat and Mass Transfer 75 (2014) 685-705. http://dx.doi.org/10.1016/j.ijheatmasstransfer.2014.04.005
  26. B. Lafouraki, A. Ramiar, and A.Ranjbar," Laminar Forced Convection of a Confined Slot Impinging Jet in a Converging Channel", International Journal of Thermal Sciences 77 (2014) 130-138. http://dx.doi.org/10.1016/j.ijthermalsci.2013.10.014
  27. A. Rattner, "General Characterization of Jet Impingement Array Heat Sinks with Interspersed Fluid Extraction Ports for Uniform High-Flux Cooling" Journal of Heat Transfer, Vol. 139 / 082201-1,( 2017) . [DOI: 10.1115/1.4036090]. http://heattransfer.asmedigitalcollection.asme.org
  28. P. Penumadu, and A. Rao," Numerical Investigations of Heat Transfer and Pressure Drop Characteristics in Multiple Jet Impingement System” Applied Thermal Engineering 110 (2017) 1511-1524. http://dx.doi.org/10.1016/j.applthermaleng.2016.09.057 1359
  29. R. Lambert and R. Rangel, "The Role of Elastic Flap Deformation on Fluid Mixing in a Microchannel", American Institute of Physics (2010); DOI: 10.1063/1.3410268. [email protected] .
  30. K. Khanafer, A. Alamiri, and I. Pop," Fluid-Structure Interaction Analysis of Flow and Heat Transfer Characteristics Around a Flexible Microcantilever in a Fluidic Cell" International Journal of Heat and Mass Transfer 53 (2010)1646–1653
  31. S. Ali, C. Habchi, S. Menanteau, T. Lemenand ,and J. Harion," Heat Transfer and Mixing Enhancement by Free Elastic Flaps Oscillation" International Journal of Heat and Mass Transfer 85 (2015) 250-264. http://dx.doi.org/10.1016/j.ijheatmasstransfer.2015.01.122
  32. A. Soti, R. Bhardwaj, and J. Sheridan," Flow-induced Deformation of a Flexible Thin Structure as Manifestation of Heat Transfer Enhancement" International Journal of Heat and Mass Transfer 84 (2015) 1070-1081. http://dx.doi.org/10.1016/j.ijheatmasstransfer.2015.01.048
  33. S. L. Ma, J. W. Chen, H. Y. Li, J. T. Yang," Mechanism of Enhancement of Heat Transfer for Plate-Fin Heat Sinks with Dual Piezoelectric Fans", International Journal of Heat and Mass Transfer,90 (2015) 454-465. http://dx.doi.org/10.1016/j.ijheatmasstransfer.2015.03.050
  34. H. Y. Li and Y.X. Wu," Heat Transfer Characteristics of Pin-Fin Heat Sinks Cooled by Dual Piezoelectric Fans" International Journal of Thermal Sciences, 110(2016)2635. http://dx.doi.org/10.1016/j.ijthermalsci.2016.06.030
  35. A. Hales, X. Jiang," A Review of Piezoelectric Fans for Low Energy Cooling of Power Electronics", Applied Energy, 321-337.
  36. M. Ghalambaz, E. Jamesahar, M. Ismael, and A. Chamkha," Fluid-Structure Interaction Study of Natural Convection Heat transfer over a Flexible Oscillating Fin in a Square Cavity ", International Journal of Thermal Sciences 111 (2017) 256-273. http://dx.doi.org/10.1016/j.ijthermalsci.2016.09.001
  37. M. Ismael, and H. Jasim," Role of the Fluid-Structure Interaction in Mixed Convection in a Vented Cavity" International Journal of Mechanical Sciences 135 (2018) 190-202. https://doi.org/10.1016/j.ijmecsci.2017.11.001