×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerSolar energy can only be used when it's sunny outside. Therefore, solar heating is only efficient during the day and decreases at night or on overcast days. Consumer energy needs have a distinct seasonal structure, and solar energy cannot completely meet those needs. In order to satisfy customer demand, energy storage is essential. In order to maximize the use of solar energy and to increase the energy and efficiency of the solar absorption system, superior thermal properties of sophisticated materials, such as phase change materials, are important [1]. In the current study, 20 kg of phase change material (PCM) is integrated with solar water heating and fed into a storage tank to enhance the solar water heating efficiency. Helical coil heat exchangers were added to the storage tank as an external load. The trials were conducted in four separate months (September 2021, April, May, and June 2022) that were chosen on the first day. The effectiveness, heat gain, and significance of the phase change material in increasing heating efficiency throughout the day were studied using a range of variables, including water volume flow rate (2, 3, 4, 6, and 8 L/min) and inlet water temperature (25, 30, and 35 °C). The results showed that, given an initial temperature of 25 °C, the daily efficiency range, was 0.58 to 0.65, and that the daily final outlet temperature was enhanced outlet temperature over 65 °C. Additionally, on all test days, the heat released by the phase change material was audible in the evening and increased the utilization time.
Conventional Refrigeration Systems (VCRS) are the most commonly used in industrial buildings and facilities. Conventional refrigeration systems are among the most energy-consuming sources in addition to causing more environmental problems and gas emissions, such as hydrocarbons (HCs) and hydrochlorofluorocarbons (HCFCs), are known to contribute to global warming and ozone depletion. Absorption Refrigeration Systems (VARS) are a good alternative to conventional refrigeration systems because they use low-grade heat sources and operate with environmentally friendly liquids. The most important of these heat sources is the heat wasted from engines, industrial processes and many other sources. The global objective of the study is a literature review on the different ways to operate the absorption refrigeration system using waste heat in engines that include exhaust gases and engine cooling water as well as renewable energy that includes solar energy. Reviews of the literature have demonstrated how the absorption refrigeration system can be used and operated using a variety of thermal sources. This study also supports the usage of ecologically friendly chillers to provide air conditioning and refrigeration, as it shows these systems have a lower performance coefficient when compared to conventional refrigeration systems.
Solar energy is the most suitable among all renewable energy options for competing with fossil fuels in desalination due to its ability to utilize both heat and power for the process. In this study, the Parabolic Trough Solar Collector (PTSC) for powering a Single Stage Flash (SSF) desalination unit was proposed for Basrah city climate, Iraq. The desalination system comprises two directly coupled sub-systems: the PTSC and the SSF desalination unit. The preheated feed brine water coming from condenser was used as a Heat Transfer Fluid (HTF) for PTSC, which gets heated to a desired temperature referred to as the Top Brine Temperature (TBT). The numerical simulations were performed via EBSILON professional 16.02 (2022) software. The effects of TBT, mass flowrate of feed brine water to get the desired TBT, solar collector area, and vacuum pressure inside flash chamber on the performance of the desalination system was studied. A major finding of the current study can be summarized as follows: The collector efficiency is enhanced eventually as TBT increases. The maximum values of distillate water in June are around 5.5, 4.56, 3.69, 2.75 and 1.85 kg/h for 12.408, 10.434, 8.3472, 6.26, and 4.1736 m² collector area respectively, when TBT 107 °C and vacuum pressure 40 kPa. For 1.598 m² collector area, the total distillate in the 1st of June amounted to 7.9 kg, with an average production rate of around 0.7 kg/h. The solar SSF system's productivity per solar collector unit area at 20 kPa, 15 kPa, and 10 kPa vacuum pressures was 4.7 kg/day/m², 5.3 kg/day/m², and 6.25 kg/day/m², respectively. The average Performance Ratio (PR) values are determined to be 0.694, 0.577, and 0.491 for 10 kPa, 15 kPa, and 20 kPa, respectively. These results are very acceptable when compared with an existing literature.
The incorporation of thermal energy storage materials (TESMs) into solar energy systems is a factor that boosts the performance of these systems. In this paper, an experimental study was addressed for enhancing the heat pipe’s thermal performance that works with an Evacuated Solar Tube Collector with Heat Pipe (ETCHP) as a solar water heater system. This is done by adding micro-zinc oxide (ZnO-MP) to the paraffin wax integrated as TESM into the evacuated tube (ET) of the system, where the evaporator section of the heat pipe is completely submerged within the micro-enhanced paraffin wax. Three experimental prototype rigs with one evacuated tube were designed, built, and tested to do the investigation. The most important parameters that have been studied in this study are the thermal resistance and the temperature distribution pattern along the heat pipe. The results show a clear indication of the decrease in the thermal resistance of the heat pipe of the proposed system compared to the system in which pure paraffin wax was incorporated. Also, it was noticed that there is a significant improvement in the temperature distribution along the heat pipe due to the improvement in the conductivity of the micro-enhanced wax compared to the pure wax.
Performance a double slope of the solar still Integrated With or without parabolic trough collector is investigated experimentally. To improve the output of a double slope solar still, a number of initiatives have been undertaken, using wax as a phase change material (PCM) with a parabolic trough collector. A parabolic trough collector (PTC) transfers incident solar energy to the solar still through a water tube connected to a heat exchanger embedded in used microcrystalline wax. Experiments were carried out after orienting the basin to the south and holding the water depth in the basin at 20 mm. According to the results obtained, the solar stills with parabolic trough collector have higher temperatures and productivity than solar stills without parabolic trough collector, as well as the ability to store latent heat energy in solar still, allowing fresh water to condense even after sunset. In addition, the parabolic trough collector with phase change material in the double slope solar improves productivity by 37.3 % and 42 %, respectively.
The Atmospheric Water Generator (AWG) is an environmental water recovery that easily dehumidifies water vapor moisture from the air. This article presents an experiment to construct an AWG model using solar energy as a source of power. An experimental and numerical study for a device of (AWG) is performed. The experimental work is performed at Basrah city, located in the south of Iraq, during August and September of 2019 and March of 2020. The theoretical results are calculated by EES and the numerical study has been conducted by the (ANSYS19/CFD/ FLUENT) program. The experimental device is tested for different days with different climate conditions. The Maximum water production obtained is 3.4 L/day from all the testing days, for different hours of operation when the relative humidity in the range of (45 – 95 %) and the temperature range from 17 °C to 45 °C. The results shown that, the water production rate is increased with increasing humidity, temperatures, hours of operation, and model size.
The solar chimney power plant is one of the modern models studied on the world. This study presents an engineering and numerical analysis of solar chimney with different parameters. Also, it studies the comparison of two collector base shapes(circular and hexagonal) depend on the five storage material types and their effects on the heat transfer, velocity, efficiency, etc. inside the solar chimney system by considering the solar array intensity equations and the energy equation to calculate the heat transferred and stored by applying the laws of CFD. The finite volume method is used to analyze the geometry physical model by applying a commercial Fluent 6.3 code with Gambit 2.3. The obtained results show that the efficiency of solar chimney is increased by increasing the area of solar glassed collector with circular base shape than the others of polygonal or rectangular one because the circular was covered large area of system. So, the circular ground collector shape for thermal storage is the favour because it is the better to increase the velocity of entering air and to increase the efficiency of turbine. In addition to that the black Pebble storage plate is the better material for heat storage which is convected to air passed for operation of turbine than the other types aluminum, tar, copper and steel seriously.