×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThis paper presents a pressure drop analysis in perforated vertical wellbores for different perforation parameters. The effect of the density of the perforations (number of perforation), the phase angle of the perforations, the diameter of the perforation and the flow rate of the crude oil from the perforations on the pressure drop and the productivity index of the perforated vertical wellbores were studied. The analysis of the vertical wellbore was performed numerically using ANSYS FLUENT 15.0 software. Three dimensional, steady-states, turbulent and incompressible fluid flow is assumed during the numerical solution of the governing equations. The results of this study show that, increased perforation density of the perforated vertical wellbore caused an increase in pressure drop, and also, decreased productivity index due to increasing the friction losses. Friction pressure drop has a significant effect on crude oil flow into the wellbore. When the main velocity is 1.5 m/s and the inlet velocity from the perforations is 2 m/s, the friction pressure drop is about 66 % and the acceleration pressure is approximately 34 % of the total pressure drop.
This paper demonstrates experimental and numerical studies to investigate in perforation pipes with a phasing 180° and perforation densities 9 spm in a horizontal wellbore. The experimental study was conducted to investigate the phasing angle 180° in a horizontal wellbore. The wellbore has an inner diameter of 44 mm, as well as the length of the pipe is 2 m. For this purpose, a simulation model was created in the wellbore using the ANSYS FLUENT simulation software by using the standard k - e model and applied to the (CFD) with changing the axial flow from (40 - 160) lit/min and constant inflow through perforations from range (20 - 80) lit/min. Concerning the findings of this study, it was noticed that the total pressure drop (friction, acceleration, mixing) goes high as the total flow rate ratio increases. As well as, an increase of the inflow concerning the main flow rate ratio leads to an increase in the total pressure drop and a decrease in the productivity index. Furthermore, the percentage error of the total pressure drop between the numerical and experimental results in test 4 is about 5.4 %. Also, the average velocity goes high with increasing the total flow rates and the velocity keeps increasing along the length of the pipe until it reaches its maximum value at the end of the pipe due to the effect of the perforations. It was concluded that there are the numerical and experimental results reflected a good agreement concerning the study of the flow-through perforations at 180° angle in terms of pressure drop and apparent friction factor, etc.
This paper presented experimental and numerical studies to investigate pressure drop in perforation horizontal wellbore with a 90° phasing and 20 spm perforation density. The experimental apparatus has been constructed to calculate the static pressure drop and calculate the exit velocity in the horizontal pipe after mixing the axial flow with the radial flow through the perforations in the wellbore. The specifications of the wellbore used were the inner diameter is 44 mm, length is 2 m, and perforation diameter is 4 mm. For this objective, a simulation model was created in the wellbore using the ANSYS Fluent simulation software by using the standard k-ε model and applied to the (CFD) by changing the axial flow from (40-160) lit/min and constant inflow through perforations from range (0 - 80) lit/min. According to the study's findings, the increase in the radial flow through the perforations increases the total flow rate ratio and the total pressure drop and vice versa. In addition, an increase in the axial flow mixed with radial flow increases the total pressure drop, friction factor, and a decrease in productivity index. Furthermore, the percentage error of the total pressure drop between the numerical and experimental results in test 4 is about 3.83 %. It was found that the numerical and experimental results represented a good agreement about the study of the flow-through perforations at 90° angle in terms of pressure drop and productivity index, etc.
A numerical simulation of the effect evaluation of heat loss and temperature distribution along the wellbore is performed, for two models, the first is an open hole (without perforation) and the other is a perforated vertical wellbore. In this study, the Computational Fluid Dynamics (CFD) software code ANSYS FLUENT 15.0 has been used, for simulate a model of 3-D turbulent flow with stander k-ϵ model. The results of this show that, increasing the heat losses leads to an increase in the temperature gradient, while the temperature gradient decreases with increasing inlet main velocity. Also, the temperature of the produced crude oil decreases with increasing the length of the wellbore.
In this study, loading was carried out for several types of perforated plates, such as circular, rhombic and rectangular holes, where the holes were arranged in two types, namely straight arrangement and alternating arrangement. The stress intensity factor and shape factor were calculated for each case, taking into account the diameter of the holes. So, it is found the SIF increases significantly when the plate is perforated, and the same applies to the shape factor, also increases. In the case of circular holes, the increases in the average value of (SIF) reached to (80.88 %) when the plate was perforated with alternated arranged of circular holes, while the straight arrangement of circular holes the increases of average values of SIF reach to (67.55 %). Either in the case of rhombus holes: the SIF values are increases to (51.07 %) when the plate was perforated with the alternated arrangement, while in the straight arrangement of holes the (SIF) increase to (35.43 %). It was observed through this study, the increases of stress intensity factor and the shape factor with different crack lengths were more stable in the plate that perforated with an alternated arrangement of holes than the straight arrangement. The higher values of stress intensity factor obtained when the plates were perforated with circular holes, due to the circular shape has more stiffness, so the Absorption of force will be small Compared with the rhombus and rectangular shape that will be less stiffness which the absorption of strength is greater.
There have been efforts and studies that have been carried out with respect to the flow patterns, pressure drops (PD), and void fraction (VF) that can be found in horizontal wells. Notwithstanding, particular attention has not been paid to research of two-phase flow (TFF) in perforated horizontal boreholes. Recently, a number of attempts have been undertaken to investigate the features of gas-liquid systems, which exist in a TFF in a perforated horizontal wellbore, which is a little studied tree of the wellbore family. The stated investigations are devoted to the TFF of liquid and gas in a horizontal wellbore, which has a diameter and length of $25.4~mm\times3$ m respectively, with 18 uniform perforations. In the developed Fluent VOF model integrated in ANSYS 22 R1, the turbulence treatment and flow conditions within three-dimensional space, including water and air, with various flow rates were used to study the influence of high water and air velocities (SVW, SVA) on flow characteristics including PD, production (Q), VF, and liquid retention time in a horizontal well. The sequences of slug flow (SF) phenomena have been studied in detail for this pulsated flow. In particular, the first scenario is where SVW can reach velocities of $1.22~m/s$ and SVA of $1.68~m/s;$ in the second scenario, an increase in the SVW to $2.52~m/s$ is noted; and in the last scenario, the value of SVA is increased to $2.2~m/s$. The empirical study was mainly targeted on the SF through a perforated horizontal wellbore. The productivity (Q), PD, and SF were found to benefit from an increase in axial flow rate (SVW), more than from increase in radial flow rate (SVA). In scenario two, productivity rises by even 84.108% as SVW changes, while in the last scenario Q increases by only 9.708% as SVA is increased. Further, the numerical and experimental results provide a reasonable match.