×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThe study investigates the behavior of reinforced concrete cylindrical shells under monotonically increasing loads. Three-dimensional models of six small-scale experimental shells with length-to-radius ratios ranging from short (0.84) to long (5.0) are implemented within the context of the finite element method, through use of the ANSYS computer code, and the nonlinear response is traced throughout the entire load range up to failure. Cracking occurs at working load levels, with subsequent reduction in shell stiffness. Increasing loads lead to failure modes varying from a beam failure in long shells, combined longitudinal and transverse cracking in intermediate length shells, and abrupt diagonal with limited transverse cracking in short shells. Ultimate load capacities range from 5.0 kPa to 60.0 kPa increasing with decreasing length-to-radius ratios.
The study investigates the behaviour of reinforced concrete corner joints under monotonically increasing loads which tend to increase the right angle between the two joint members. The experimental results for two case studies are considered, and the ANSYS computer code is employed to create three-dimensional models for corner joints within the context of the finite element method. The effect of reinforcement details at the corner joint is studied for commonly used detailing systems, and the nonlinear response is traced throughout the entire load range up to failure. The results obtained are generally in good agreement with the experiments, and show that the detailing system has a significant effect on corner joint behaviour, with efficiencies ranging from as low as 54% up to 147%.
In recent decades, the need for strengthening and repairing reinforced concrete structures has increasingly arisen. One common method is the use of concrete jackets. Slurry Infiltrated Fiber Concrete (SIFCON), a newly developed material, offers superior mechanical properties, making it a preferred choice for strengthening and repairing concrete structures. However, there is limited understanding of its bonding performance when used as an overlay on a Normal Strength Concrete (NSC) substrate. This study conducted a direct Shear Test (DST) to evaluate the bond performance using reinforced NSC cubes externally bonded with SIFCON jackets subjected to direct shear. Eighteen reinforced cubes were strengthened with various bonding systems to investigate how different factors affect the bond performance between the NSC substrate and SIFCON overlay. The parameters studied included surface preparation methods, binder types, jacket configurations, bonding conditions (fresh overlay on hardened substrate and hardened overlay on hardened substrate), dowel placement, and bonding mechanisms. The results show that using bonding agents significantly improved bond strength, with epoxy proving more effective than latex. Specimens prepared by chipping showed better bonding performance compared to those prepared through diamond cutting. Chipping increased bond strength by 8.91% to 13.84% over diamond cutting in the case of fresh SIFCON overlay on hardened substrate. Using dowels in the bonding systems also improved bond performance by 10.89% to 16.97%. Applying jackets to three sides instead of two increased the ultimate failure load by 31.76% when dowels were used in both the two-sided and three-sided strengthened samples, and by 35.45% in the absence of dowels in both types of strengthened specimens. The cast-in-situ specimens demonstrated superiority over those strengthened with precast jacket layers.
Concrete roof-folded plates have been shown to be inherently resilient to earthquakes, despite limited research on the reasons for their apparent seismic resistance. It is possible to make very thin, folded concrete plates because of their high structural efficiency. It is implicitly resistant to earthquake forces because thin, folded plat structures are relatively lightweight. Typically, folded plate structures are designed to perform under ideal gravity loads that are transported primarily as a result of membrane activity across the surface. It is possible for concrete-folded plate structures to be damaged by bending stresses when earthquakes induce unexpected horizontal forces. Through a parametric analysis of an 8-cm-thick concrete roof folded plate structure, it has been shown that thin concrete roof folded plates with a span < 30 m can be intrinsically earthquake-resistant. Despite having a low mass and high geometric stiffness, these buildings have fundamental frequencies that are substantially higher than those connected to seismic events that actually occur. This characteristic causes the folded plate to behave elastically under earthquake excitation without exceeding the maximum concrete strength. The vertical components of earthquake vibrations exert greater stress on a shallow, folded plate than the horizontal components. The values of the stresses imposed by the changing span were relatively small. They ranged from (3.5-4.4) MPa for the Landers earthquake, while for the El Centro earthquake, they ranged from (2.7-8.6) MPa. In addition, by raising the folded big plates and inclining them to a greater angle, it will become more common and lessen the harm caused by earthquake shaking in the vertical direction. In general, this paper aims to present an examination of earthquakes and their consequences for folded concrete plates.
The reason for the widespread use of steel box girders is that they have high structural efficiency due to the high bending, high torsional stiffness and rapid erection. For bottom flange of the girders, the buckling behavior during production and erection due to compression strength can be a problem. The compression plate with longitudinal stiffeners typically renders an economic. The optimal design of longitudinal stiffeners is discussed. The results are based on 3-D FEA (ANSYS19.2) of many stiffened compression bottom flange models, the moment of inertia requirement of bottom flange longitudinal stiffener is investigated by studying the effect of many parameters as longitudinal stiffeners numbers, stiffener sections, plate aspect ratio and compression flange thickness. Also, the stiffeners effect on the compression panel plate stresses were studied by modeling girder with and without longitudinal stiffeners. The finite element method is useful as they can be used to study the plate with stiffeners in an economical way, and we don’t need experimental and laboratory tests.
During the pouring of concrete deck, the installation of external bracing between the inner and outer girders may be necessary when the bridge has sharp curve in order to control the deflection and rotation of the girders. However, it is important to minimize the number of external bracing members, as they have expensive cost and they also have opposite effects for the fatigue features of the steel tub girders. The analysis of curved box girder bridges is carried out numerically by the use of finite element method through (ANSYS 19.2) software. The curved box girder with the intermediate external diaphragms was modeled and the analysis was carried out for many parameters like external bracing sections, girders with or without concrete deck, girders with end diaphragms or without them. The study concluded that ANSYS program has a good ability in evaluating the external bracing force comparing with code equations.