×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThe aim of this study is to investigate the effect of heat treatments on the impact properties of hot rolled high strength steel and describes the effect of tempering temperature and quenching media on the microstructure, hardness, and impact resistance of plates. In the present study a high strength steel was austenitized at 900 °C with different quenching medium and followed by tempering at 300 °C, 500 °C. After thermal treatments, the values of Charpy impact resistance, hardness, and microscopic structure were evaluated from mechanical and metallographic analysis of metals respectively. The change of mechanical properties and microstructure of the metal with the existence of heat treatment with the ballistic performance of high-strength steel. Experimental results showed that tempering at 500 °C for 2 hours after water quenching medium it provides the best mechanical properties in conjunct on with an improved in microstructure.
Four groups of AISI 1020 specimens were heat-treated at 850 °C in a muffle furnace for 30 minutes then quenched in oil. The samples were tempered at 400 °C with a time period for each group as (group B, 2 hours), (group C, 3 hours), and (group D, 4 hours). The mechanical properties of the samples were studied using universal tensile testing equipment and a Brinell hardness testing machine. The hardness values of the quenched samples were calculated from a given modified equation. The torsional fatigue behavior of AISI 1020 was discovered in this investigation for heat-treated specimens and compared with the original specimens. All groups were subjected to an analysis using an optical microscope. Pearlite is formed when is heated in the austenitic region and then cooled below a lower critical temperature. It was concluded that the heat treatment increases the hardness for the specimens while decreased the shear fatigue ductility coefficient. Also, the heat treatment increased the shear fatigue strength coefficient. Furthermore, increasing in the time period of the tempering process was leaded to decrease the coefficient of shear fatigue strength and increased the coefficient of shear fatigue ductility.
AISI 4330 Low-alloy steel is good material for advanced application because of its properties including strength and longevity. However, performance may be modified with heat treatment procedures, include quenching and tempering. These processes can create residual stresses and retained austenite (RA), which have an effect on the metal's application. these factors influence fatigue life, dimensional stability, and fracture toughness of engineered components. uncontrolled residual stresses can reduce fatigue strength by up to 30%, while optimal retained austenite content (e.g., 5-10%) can enhance damage tolerance. This study focuses on residual stresses and retained austenite measurement in AISI 4330 low-alloy steel after heat treatment. including experimental and simulation methods. The review summarizes many scientific studies published between 2019 and 2024 and shows some main challenges. One challenge is the difference between experimental results (for example, from X-ray diffraction (XRD) and neutron (diffraction) and simulation results (especially using ANSYS software). Another challenge is that different methods for measuring retained austenite can give different results, which can change how we understand the steel's properties. The review also explains new progress in modeling heat treatment. This includes adding phase transformation models to finite element simulations. Future efforts should combine multiscale simulation, characterization, and machine learning to achieve predictive control over these properties in manufacturing.
The present study aims to investigate the influence of heat treatment and surface finish on the behavior of crevice corrosion resistance of AISI 410 and 416 martensitic stainless steels thus, to quantify the conditions at which crevice corrosion minimize as possible. The experimental work carried out during this study involves material selection, chemical composition tests, specimens preparation before heat treatments, austenitizing at temperature range (925-1010˚C) and for holding time periods of (30, 45 and 90 min), air and oil quenching followed by tempering at heating range of (205- 605 ̊C) and for 45 min, micro hardness tests, specimens grinding, surface roughness measurements, crevice corrosion tests, crevice evaluation and microstructure tests. Theoretically, empirical equations for crevice maximum depth under the effect of surface roughness and hardness for both AISI 410 and 416 steels were determined. While for microstructure analysis, carbides average area was determined by using the ImageJ analysis program and a mathematical model was also predicted. Results showed that, as hardness and surface roughness increase crevice corrosion resistance decreases. Therefore, material treated by annealing can minimize crevice corrosion rates more than that treated with hardening.