×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThe conjugate natural convection-conduction heat transfer in a domain composed of nanofluids filled porous cavity heated by a vertical solid wall is studied under steady-state conditions. The vertical left wall of the solid is kept isothermal at hot temperature Th. The vertical right wall of the solid is in contact with the nanofluid saturated porous medium contained in the cavity. The right vertical wall of the cavity is kept isothermally at the lower temperature Tc. The upper and lower horizontal walls are kept adiabatic. The governing equations of the heat transfer in the solid wall and heat and nanofluid flow, based on the Darcy model, in the nanofluid-saturated porous medium together with the derived relation of the interface temperature are solved numerically using the over-successive relaxation finite- difference method. A temperature independent nanofluids properties model is adopted. The investigated parameters are the nanoparticles volume fraction (0-0.2), Rayleigh number Ra (10-1000), solid wall to base-fluid saturated porous medium thermal conductivity ratio kwf (0.1, 1, 10), and the solid wall thickness D (0.05-0.5). The results are presented in the conventional form; contours of streamlines and isotherms and the average Nusselt number. At a very low Rayleigh number Ra=10, an enhancement in heat transfer within the porous cavity with is observed. Otherwise, the heat transfer may be unchanged or deteriorated with depending on the wall thickness D and the conductivity ratio kwf.
This numerical study aims to enhance the heat transfer efficiency by dissipating the heat Emitted from electronic processors. A jet impingement technique is utilized with porous layer covering a metal fin as a heat sink. Forced convection and normal convection (due to the buoyancy effect) are taken into consideration. The two equations model (Local Thermal Non-Equilibrium LTNE) employed to describe the energy equations of the two phases of the porous surface. Finite Element Method (FEM) used to discretize these equations to obtain the numerical solution. To make this study closest to the reality, constant heat flux boundary condition is applied underneath the metallic heat sink. The geometry comprises of three domains: Free flow channel, Porous layer and Metal fined heat sink. In order to simulate the heat transfer, isotherms; streamlines and Nusselt number have been considered. Investigation has been done by inspecting the effects of the pertinent non- dimensional parameters such as: Reynolds number ( Re = 100-900), Darcy number ( Da = 10 -1 -10 -6 ), Richardson number ( Ri = 0.1-100) and Porosity ( ε = 0.85-0.95). The results show that increasing Re and decreasing ε lead to enhance Nusselt number. Richardson number below 100 has no significant effects on Nu . At Re above 400, Nusselt number proportional with Darcy number. The enhancement of Nusselt number is found to be 250 % by increasing Re from 100 to 900, 290 % by decreasing ε from 0.95 to 0.85 and about 13 % by increasing Darcy number from 10 -6 to 10 -1 .
The panel absorbed solar radiation and majority of this radiation is transform into a heat, and it is usually wasted and useless. At higher cell temperature, the current out of the cell has an unnoticeable rise, but the voltage value will drop significantly, resulting in a reduction in maximum power produced. The cooling method is therefore beneficial to keep the panel at the operation temperature. A simulation model is developed using COMSOL Multiphysics software version 3.5 software to investigate the enhancement in performance of a PV water cooling module (PVW module) based on a passive and simple cooling technique using a wetted cotton porous wick attached on the PV panel's back side and compare with uncooled PV panel (PVREF module). Unsteady, laminar and 2-D, the flow in the proposed modules is assumed. The input parameters were taken from a real weather condition was perform in Najaf-Iraq. The effect of variation of mass flow rate is also studied in the present work. Good agreement was obtained for PVREF module with previously researches.
Natural convection heat transfer in porous cavity with arc shape wall filled with nanofluid is studied numerically. The right arc shape wall of the cavity is heated at constant temperature (Th) while the left wall is kept cold at constant temperature (Tc), and the other horizontal walls are thermally insulated. The governing equations of the heat transfer and nanofluid flow are solved Flex PDE software. A temperature independent nanofluids properties models are adopted. The investigated parameters are the nanoparticles volume fraction Ø= (0-0.2), Rayleigh number Ra (10-1000) and arc center Ce (1-∞). The results are presented by contour of streamlines, isotherms and the average Nusselt number. The results have showed that the average Nusselt number decreases with increasing Ce and increases with increasing Ra and Ø.
The natural convection heat transfer in a porous media filled and isothermally heated from the bottom wall of triangular enclosure is analyzed using finite element software package (FLEXPDE). Darcy's law was used to write equations of porous media . The curved bottom wall shape, with Radii R= 0.8 , 1 and 1.5, was applied to a triangular enclosure. The boundary condition of the vertical wall is isothermal and of the inclined wall is adiabatic. The study was performed for different Rayleigh numbers (100 ≤ Ra ≤ 1000 ) and aspect ratios (0.4 ≤ AR ≤ 1 ) . Numerical results are presented in terms of streamlines, isotherms and Nusselt numbers. It was observed that heat transfer enhancement was formed with increasing Rayleigh number and aspect ratio . A comparison of the flow field and isotherm field is made with that obtained by [11], which revealed a good agreement .
The ability to predict the performance of a petroleum reservoir is of immense importance for the petroleum industry. Numerical simulation is the most powerful tool that can be used for reservoir performance prediction. In the current study a new simulator has been designed for two phase compressible oil water flow through compressible porous media. The new simulator is able to treat the frontal advancement and the high rate of change region by static and dynamic local grid refinement. A new approach is proposed in this study to trace the frontal advancement. The proposed simulator has been applied to several field reservoir cases and show good performance.
Constructed wetlands are engineered systems used for wastewater treatment with the objective of reusing water under controlled conditions by mimicking natural treatment mechanisms involving porous media, plants, and microbial communities. This study investigates the performance of a horizontal subsurface flow constructed wetland, where wastewater flows through a gravel bed and vegetation roots, allowing contact with biofilm developed within the wetland substrate. To evaluate treated water quality, physical, chemical, and biological parameters were measured. Field results demonstrated that pollutant removal efficiency increased with detention time. After 3, 4, and 6 days of treatment, average removal efficiencies were 47.7%, 53.2%, and 77.5% for COD; 45.1%, 52.8%, and 64.4% for total nitrogen (TN); and 55.4%, 58.8%, and 72.2% for ammonium (NH₄), respectively. Nitrate removal averaged 19.41% after 3 days. These findings confirm that the horizontal flow constructed wetland system is effective in reducing key wastewater pollutants.