×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThis paper aims to investigate the effect of Ag nanoparticles addition in different percentages (0.12 wt. %, 0.15 wt. %, 0.25 wt. %, 0.35 wt. %) on the microstructure properties of Cu-21%Zn-6%Al shape memory alloy. Optical and SEM were carried out to studied such effects. Two heat treatments were carried out at (825 ℃ and 850 ℃) for 10 min and quenched in ice water. It was observed that both of heat treatment lead to formation M18R martensite with V-shape and needle like, but raising the temperature of heat treatment from 825 ℃ to 850 ℃ lead to a decrease formation α phase, which leads to improving the shape memory properties. Refinement of the grain size resulted as Ag nanoparticles addition increased from 0 to 0.25 wt. %, the grain size decreases from 1551 μm to 212 μm with reduction of 86.32 wt. % at 0.25 wt. % Ag. The microstructure observation indicated that the Ag nanoparticles addition leads to creating a multi-variant oriented martensite microstructure after quenching process in ice water.
Nanoparticles show mechanical, electrical, chemical and optical properties that are different and superior to bulk materials. In the present work, α-Alumina nanoparticles were synthesized using the nonorganic Sol-Gel method under controlled conditions. Because of the low cost of its raw materials, low manufacturing temperature and the high purity of the product, Sol-Gel method is the best in the manufacture of nanostructures like metal oxide nanoparticles. The precursor of the Sol-Gel process was aluminum nitrate with ethanol. The prepared nanopowder was evaluated by X-ray diffraction (XRD), scanning electron microscope (SEM), electron dispersive spectroscope (EDS) and Malvern Zetasize analyzer.
This article provides an overview of the studies that have been conducted on the characteristics of epoxy resins containing various types of silica nanoparticles and microparticles, as well as their performance in the industrial application of functionally graded materials (FGMs). Silica nanoparticles and microparticles are used to create epoxy resins in order to improve various properties, such as thermal stability, adhesiveness, electrical conductivity, strength, modulus, and toughness. This review examines the literature that has been published in the last decade, compares the results, focuses on the mechanical and thermal properties, and discusses the changes that have resulted in improvements in those properties. Previous experimental findings are presented and contrasted to demonstrate the extent to which silica filler content contributes to improving the properties of composite materials. The findings reveal that the characteristics of epoxy compounds can be improved by adding a particular amount of silica particles. There is a correlation between an increase in the silica amount and an increase in the Young modulus of epoxy compounds, this correlation becomes stronger as the silica amount increases. Additionally, the tensile strength of epoxy compounds increases to a certain limit as the amount of silica nanoparticles increases. In contrast, the hardness of the material increases as the silica amount increases. The density of the material also increases steadily as the silica amount in the material increases. According to thermal analysis results from calorimetric research on epoxy–silica systems, the glass transition temperature increases as the silica amount increases.
Zinc and its alloy coatings are commonly used to provide cathodic protection for weathering steel. However, the steel substrate corrodes faster than the Zinc coating because of the coating's negative corrosion potential. Many studies have examined Zinc and alloy coatings' resistance to corrosion. Hot-dip galvanizing, Electrodeposition, and Zinc-rich coat (ZRC) spray are just some of the methods that can be used to deposit such coatings. Commercially available 99.95 % pure Zinc oxide was used in the electroplating process in this investigation. Steel samples were plated in Zinc sulphate and Zinc oxide solutions and were controlled by different bath parameters such as voltage, current, pH, temperature, and coating time. The addition of hexagonal Boron Nitride (h-BN) nanoparticles has also shown significant improvements in corrosion resistance. However, Zinc-based coating techniques reinforced with h-BN incorporation show the best corrosion current density ( I corr ) of Hot dip 2 % wt. (2.1 µA/cm 2 ), ZRC 2.5 % wt., (4.4 µA/cm 2 ), and electroplating 15.75 g/L (0.081 µA/cm 2 ), which is an order of magnitude lower than coatings without h-BNs. The corrosion rates and current densities of Zn/h-BN coated layers were investigated in a controlled laboratory environment that mimicked natural conditions (Rainwater solution) by extrapolating polarization curves.
In this work, the turbulent buoyancy driven fluid flow and heat transfer in a differentially heated tall rectangular enclosure filled with nanofluid is quantified numerically. The two dimensional governing differential equations (continuity, momentum, energy and low Reynolds number LRN k-ω turbulence equations) are discretized using the finite volume method. SIMPLE algorithm is employed to obtain stabilized solution for high Rayleigh numbers. Two types of nanofluids namely, Al2O3-water and Cu-water, were considered. The effect of Rayleigh number (1010 to 1012), diameter of nanoparticles in the range 25-100 nm, nanoparticle volume fraction in range 0-0.08 and the aspect ratio (30, 40 and 50) on fluid flow and heat transfer are investigated. The present results are compared with previously published work and a qualitative agreement with good validation is obtained. Results show that addition of nanoparticles makes the liquid be more viscous which decreases the vertical velocity component and also decreases the temperature gradient near the walls. Also an announced heat transfer enhancement is obtained with nanoparticle volume fraction reaching a maximum point called optimal volume loading, at which the maximum convective heat transfer is obtained, and then it decreased with further increase of volume fraction.
The conjugate natural convection-conduction heat transfer in a domain composed of nanofluids filled porous cavity heated by a vertical solid wall is studied under steady-state conditions. The vertical left wall of the solid is kept isothermal at hot temperature Th. The vertical right wall of the solid is in contact with the nanofluid saturated porous medium contained in the cavity. The right vertical wall of the cavity is kept isothermally at the lower temperature Tc. The upper and lower horizontal walls are kept adiabatic. The governing equations of the heat transfer in the solid wall and heat and nanofluid flow, based on the Darcy model, in the nanofluid-saturated porous medium together with the derived relation of the interface temperature are solved numerically using the over-successive relaxation finite- difference method. A temperature independent nanofluids properties model is adopted. The investigated parameters are the nanoparticles volume fraction (0-0.2), Rayleigh number Ra (10-1000), solid wall to base-fluid saturated porous medium thermal conductivity ratio kwf (0.1, 1, 10), and the solid wall thickness D (0.05-0.5). The results are presented in the conventional form; contours of streamlines and isotherms and the average Nusselt number. At a very low Rayleigh number Ra=10, an enhancement in heat transfer within the porous cavity with is observed. Otherwise, the heat transfer may be unchanged or deteriorated with depending on the wall thickness D and the conductivity ratio kwf.
This study focuses on the design and construction of an automated device for evaluating the scratch resistance of polymeric materials by measuring the force required to produce surface scratches and calculating the corresponding friction coefficient from device input–output data. The device was fabricated using locally available materials, with several components manufactured in local mechanical workshops. It comprises four main subsystems: mechanical components, scratching mechanism, electrical and electronic units, and an operating control program. The developed device offers the following specifications: normal load range of 0.1–325 N, sliding speed of 1–35 mm/s, tangential force measurement capacity of 0.1–294 N via a load cell, sample dimensions of 10–195 mm in length, 10–125 mm in width, and 0.25–50 mm in thickness, a maximum scratch length of 195 mm, and an adjustable indenter height ranging from 0.25 to 50 mm above the platform surface. Scratch testing and friction coefficient measurements were conducted on pure PMMA and PMMA reinforced with silicon dioxide (SiO₂) nanoparticles. Experimental results demonstrated increased scratch resistance and reduced friction coefficients with higher SiO₂ weight ratios. Additionally, the performance evaluation confirmed that the designed device is capable of accurately and rapidly measuring the tangential forces associated with scratching through a simple operational procedure.
Natural convection heat transfer in porous cavity with arc shape wall filled with nanofluid is studied numerically. The right arc shape wall of the cavity is heated at constant temperature (Th) while the left wall is kept cold at constant temperature (Tc), and the other horizontal walls are thermally insulated. The governing equations of the heat transfer and nanofluid flow are solved Flex PDE software. A temperature independent nanofluids properties models are adopted. The investigated parameters are the nanoparticles volume fraction Ø= (0-0.2), Rayleigh number Ra (10-1000) and arc center Ce (1-∞). The results are presented by contour of streamlines, isotherms and the average Nusselt number. The results have showed that the average Nusselt number decreases with increasing Ce and increases with increasing Ra and Ø.