×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThis numerical study was conducted to simulate and analyze the pushout test for the new shear connector in a new steel-concrete composite system. In this system, the shear stirrups of the reinforced concrete beam are used as shear connectors when passed through holes drilled in the web of inverted steel T-section. The numerical analysis was performed by creating a three-dimensional finite element model using the finite element program ANSYS 21 student version to simulate the behavior of the new innovative shear connectors. The pushout specimens analyzed in this study have been tested experimentally by the same researchers earlier. A total of fifty-six push-out specimens were modeled and analyzed to investigate the effect of many parameters on the shear strength and slip capacity of the shear connector. The parameters studied in this investigation were the specimen dimensions (length and width), the diameter of stirrups (shear connector), the number of connectors per specimen, concrete strength, size of T-section, and shape of the specimen. The finite element analysis using ANSYS gave a good prediction of the effect of studied parameters on connector strength, the failure modes, the form and intensity of deformations in the model, and the load-slip response. The maximum difference in connector strength which was observed between the numerical and experimental results was 15 %.
The shear panels of plate girder made from corrugated in the web is investigated in this research. A corrugated web beam of plate is attached in the shear zone of the web as part of an experimental and theoretical investigation into plate girders. In experiments, seven plate girder specimens were tested under two points of load. Six of them were made of different shape of corrugated plate in the web, the last specimen was tested without corrugation as a reference specimen called control. In this study investigated the effected of (corrugation plate, thickness of corrugation with number layers of corrugated and the shape of corrugated plate) on (buckling and ultimate loads also on lateral and vertical deflection) and compared with reference specimen, these specimens have the same dimensions, the main variable was the thickness of the corrugated plate in the web (0.5, 1, and 2) mm, the depth was constant (300 mm). According to results of the experiment, the corrugated plates primarily increase the plate girder's stability. A corrugation of plate increases the buckling load and ultimate load significantly through the contribution of the corrugation to delay buckling of the plate girder in the web. In addition, it was found that increasing the plate-girder thickness leads to increased buckling and ultimate loads, because the stiffness will increase and delay the buckling. Also, the trapezoidal corrugation and the diagonal corrugate that placed perpendicular on the tension field action, give higher buckling and ultimate load than control beam. Ansys (version 17.0) computer program was used in this research represent the steel and nonlinear large structural shell was used to represent the corrugated web beam of the plate in the finite element analysis model.
New composite reinforced concrete beams, in which reinforced concrete component is connected to steel T-section, are proposed. The stirrups of the beam were utilized as shear connectors by passing them through drilled holes in the web of the steel T-section. Experimental test and numerical analysis were conducted to determine the behaviour of such beams when subjected to combined shear, torsion, and bending stresses. Full scale one conventional reinforced concrete curved in plan beam C1, and four composite reinforced concrete ones, C2 to C5, were tested. The degree of shear connection between the two components of beams C2 to C5 was changed by varying the number of stirrups which are used as shear connectors. The increase in load carrying capacity of the composite reinforced concrete beams reached 55 % for beam C4 as compared to that of ordinary reinforced concrete beam. The experimental results demonstrated that the stirrups are very effective in providing the interaction between the two components of the beams. The degree of shear connection emerged not to have effect on the behaviour of tested beams. Three-dimensional finite element analysis was conducted using commercial software ABAQUS. To model the shear connection in composite reinforced concrete beam, the stirrups were connected to the web of the steel T-section by springs at the location of the stirrups. Good agreement is obtained between the results of the experimental tests and the finite element analysis.
The present investigation's main goal is to assess butt joint and T-joint plates containing misalignment, undercut and porosity welding defects by studying the influence of the defect’s parameters on the fatigue life. The fatigue life is predicted using ANSYS ver. 19 Software. The results of finite element analysis are used in the regression analysis to find relationship between the fatigue life and defects parameters. The findings demonstrated that finite element modeling and the pervious published experimental tests were in good agreement with maximum error percentage 4 %. The fatigue life differed substantially depending on the defect’s parameters.
The finite element method is used to simulate the soil vibration behavior due to the Basrah-Baghdad passenger train and its effect on a targeted building in the Al-Ma'qal quarter, Basrah governorate. Three-dimensional dynamic elastic analyses are performed to calculate the particle velocities for a train speed of 120 km/hr. The effectiveness of screening using active (10 m long) open trench barriers with variable depth (2 m - 5 m) and width (0.4 m - 0.8 m), is being studied. For a given trench width (0.4 m), the results of the parametric study revealed a considerable effect of trench depth where the screening capability near the trench is increased by (10.4 %, 26.1 %, 36.3 %) due to a (50 %, 100 %, 150 %) increase in depth. The results are less sensitive to the variation in trench width. The screening capability of a double open (0.4 m × 10 m × 2 m) trench system was also investigated, where a mitigation improvement of (36.4 %) was achieved. The vibration mitigation using single and double trench systems, filled with (40 %) rubber content mixture, was also analyzed. It is concluded that using the additional passive trench increases the mitigation of the single system by around 19.1 %. An important finding is that the (40 % rubber + 60 % native cohesive soil) mixture proved to be a good filling material, since the infilled-trench systems produced comparable screening ratios to the open systems, where (97.7 %) and (85.4 %) were accomplished for the single and double systems, respectively.
A composite beam is an accumulation of different materials so as to form a single unit to exploit the prominent quality of these materials according to their position within the cross-section of the composite beam. The present study investigates the structural behavior of six simply supported composite beams, in which a reinforced concrete T-beam is connected together with a steel channel located at the bottom of a T-beam by means of headed stud shear connectors. The used degrees of shear connection are (100%, 75%, 50%, and 38%). Three dimensional nonlinear finite element analysis has been used to conduct the numerical investigation for the general behavior of beams which are subjected to central point load. ANSYS 12.1 program code was used to estimate the ultimate loads, deflections, stresses, strains, end slip. Concrete was modeled by brick element (SOLID65), while the steel channel was modeled as brick element (SOLID45). Two-node discrete elements (LINK8) are used to represent the steel reinforcement and shear connectors. Perfect bond between the reinforcing rebars and the concrete was assumed. The load on beams was applied monotonically in increments up to failure. The reduction of the degree of shear connection from 100% to 38% causes increasing of strain, mid span deflection and end slip with an average of 3.95%, 13%, and 111% respectively, while the ultimate load decreases with an average of 7.3%. In order to observe the efficiency of the 3-D model, a comparison was made with available experimental work. Good agreement was obtained throughout this work between the finite element and available test results.
An investigation was conducted to study the effect of loading level with respect to shear center and span length on lateral torsional buckling of steel I-section beams using linear and nonlinear finite element analysis available in ANSYS (version 12.0) computer program. The steel beams which have been studied included prismatic beams and linearly web- tapered beams with web tapering ratio of (0.5). The maximum height of all beams was 300 mm with span length of 4, 6 and 8 m. The critical buckling loads for prismatic and linearly tapered cantilever and simply supported beams subjected to point load and uniformly distributed load were determined. The results showed that, the bottom flange loading gives a buckling loads higher than that of the top flange loading with percentage increases of 148% and 155% for the linear and nonlinear analysis respectively for the prismatic beams. While for the tapered beams, these percentages increases were 61% and 67% respectively.
The study investigates the behavior of reinforced concrete cylindrical shells under monotonically increasing loads. Three-dimensional models of six small-scale experimental shells with length-to-radius ratios ranging from short (0.84) to long (5.0) are implemented within the context of the finite element method, through use of the ANSYS computer code, and the nonlinear response is traced throughout the entire load range up to failure. Cracking occurs at working load levels, with subsequent reduction in shell stiffness. Increasing loads lead to failure modes varying from a beam failure in long shells, combined longitudinal and transverse cracking in intermediate length shells, and abrupt diagonal with limited transverse cracking in short shells. Ultimate load capacities range from 5.0 kPa to 60.0 kPa increasing with decreasing length-to-radius ratios.
The study investigates the behaviour of reinforced concrete corner joints under monotonically increasing loads which tend to increase the right angle between the two joint members. The experimental results for two case studies are considered, and the ANSYS computer code is employed to create three-dimensional models for corner joints within the context of the finite element method. The effect of reinforcement details at the corner joint is studied for commonly used detailing systems, and the nonlinear response is traced throughout the entire load range up to failure. The results obtained are generally in good agreement with the experiments, and show that the detailing system has a significant effect on corner joint behaviour, with efficiencies ranging from as low as 54% up to 147%.
This study investigates the deep drawing process of carbon fiber-reinforced high-density polyethylene (CF-HDPE) composites through experimental and numerical approaches. The experimental part involved fabricating CF-HDPE sheets and conducting deep drawing operations under controlled parameters (punch speed, temperature, and forming depth) to evaluate material behavior and mechanical properties. Numerically, finite element analysis (FEA) using ABAQUS simulated the forming process, analyzing stress distribution, strain development, and material deformation under varying conditions. Results revealed that increasing forming depth and decreasing forming temperature elevated the required forming force. Comparisons between experimental and numerical outcomes showed consistent trends, though some differences arose due to factors like friction and material nonlinearity. The findings contribute to optimizing deep drawing processes for composite materials, enhancing manufacturing precision, and minimizing material defects.
This research concerns with the fracture behavior of reinforced concrete beams without shear reinforcement numerically. The software ABAQUS is adapted to simulate the crack propagation using the eXtended Finite Element Method (XFEM), taking into account materials nonlinearities using concrete damage plasticity CDP criteria. XFEM is used to solve the discontinuity problems in the simulation. The maximum principal stress failure criterion is selected for damage initiation, and an energy-based damage evolution law based on a model- independent fracture criterion is selected for damage propagation. The traditional nonlinear finite element analysis is used to specify the crack initiation position, which is required to specify the crack location in the analysis of beams using XFEM. Three-dimensional reinforced concrete beam models are investigated subjected to three and four-point loading tests. Simply supported beams under the effect of applied static load are investigated. An elastic perfectly plastic model is used for modeling the longitudinal steel bars. The main variables considered in the study are beam depth and the shear span with beam length. The numerical results are compared with the available experimental results to demonstrate the applicability of the model. The XFEM provides the capability to predict the concrete member fracture behavior.
The purpose of this paper is to determine a stress intensity factor experimental and numerically in the linear region by using a CT specimen of ductile material with a thickness of 15 mm, a width of 30 mm, and pre-crack 1.3 mm this dimension according to ASTM-E399-12 [1], by pulling the specimen in a 600 kN universal testing machine at a very slow speed rate of 0.5 mm/min. The load is applied until the fracture is accrued, the computer-controlled universal testing machine gives the value of the load and the displacement transducer gives a crack mouth opening displacement. The result showed experimental K I is equal to 75.412 MPa √ m, and numerical K I is equal to74.576 MPa √ m, this test showed a very slight decrease in FEA stress intensity factor compared to that in an experimental result which means the stress intensity factor, K I remains very close between experimental and numerical with an error percentage of about (1.12 %). The finite element analysis provides the best approximation to true fracture toughness values, and it can be used to acquire close parameters if experimental testing is not possible.