×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerIn this paper, energy and exergy concepts have been carried out on one of the largest gas turbine power plants in Iraq (Rumaila-Basra). Both ISO operating conditions as well as actual operating data recorded for one month in hot season are considered. Results indicate that a lot of heat energy accompanied with remarkable exergy is discharged to the atmosphere. Also, it is found that the combustion chamber has the largest exergy destruction among the plant components. Possibility of cooling the intake air drawn by the compressor and its effects on the plant performance is studied. The required cooling load is found to be in the range 3379 T.R for part load operation to 4723.3 T.R for full load operation.
In This paper, an experimental study was carried out on a dual channel with perforating “V” corrugated absorber plate of solar air collector which the air flows both in upper channel and lower channel of the absorber plate for increasing heat transfer coefficient and improving thermal performance. The results of experimental procedures for dual channel with perforating “V” corrugated absorber plate of solar collector were compared with the flat plate dual channel of solar collector. Experimental calculations had been performed under Baghdad (33.34° North latitude, 44.4° East longitude) climatic conditions at different values of mass flow rates 0.021 kg/s, 0.027 kg/s and 0.32 kg/s. The results showed that the dual channel with perforating “V” corrugated absorber plate of solar collector is found to perform more efficiently than the flat plate dual channel of solar collector with increased 39% in thermal efficiency. Then, it showed that the efficiency increases with increasing mass flow rates. Also, it showed that the heat removal factor of the dual channel with perforating “V” corrugated absorber plate of solar collector is 36% more than the flat plate dual channel of solar collector. At the last part of the study, the exergy relations were derived for both collectors. The results of this part showed that the flat plate dual channel of solar collector is having largest irreversibility (exergy loss) and the dual channel with perforating “V” corrugated absorber plate of solar collector is having a greatest exergetic efficiency.
A household refrigerator represents an essential device for all houses nowadays. The electric energy consumed by the refrigerator and the fluctuation of the temperature inside the fresh food cabin is the main two problems affecting its performance. Incorporating phase change material (PCM) inside the refrigerator is one of the solutions for the previous mentioned problems. In the present study, a water PCM is added to the cabinet of 220-litters double door refrigerator. The PCM (0.5 ml of water) is added at three different locations, touch the front of the evaporator part inside the cabin, touch the rear of the evaporator part in the cabin, and far away from the evaporator part inside the cabin. The location of the PCM determines how much energy is released and stored from the evaporator. The use of phase change material (PCM) touch to the evaporator increases the rate of heat transfer due to the conduction method being used throughout the whole heat transfer process from the evaporator to the phase change material (PCM), which raises the refrigeration system's COP (coefficient of performance). The experimental test period is 24 hours for each day. Firstly, the refrigerator is tested without using PCM, and the power consumption, the temperatures at different points for the refrigerator, suction pressure, discharge pressure, the ambient temperature, and the time on period and time off period of the compressor are measured. Secondly, for same testing period all previous parameters are measured with using PCM at different locations inside the refrigerator. The results show that, adding the PCM (water) behind the evaporator led to increase the COP by 21.97%, increase the compressor off time by 73 minutes, reduction in power consumption of 14.4%, decrease of exergy losses of the system by 8% and temperature fluctuation reduced inside the fresh food cabin, that enhance the quality of stored food. Adding the PCM front the evaporator improve the previous parameters but less than that of the first case. The third location, adding the PCM far away from the evaporator has no improvement on the refrigerator's performance.
Thermal steam power plants represent the most important and dependable type for supplying the base load of electricity around the world. The thermos-economic analysis is an important tool for improving the performance of thermal steam power plants. In the present study, a thermo-economic analysis of a simple steam power plant for different boiler pressure was performed. The analysis comprises the energy, exergy, entropy, economics, and exergy-economic of a simple cycle steam power plant for different boiler pressure. The analysis was performed for a simple steam power plant with the constant output power of 10 MW and the boiler pressure is varied from 10 bar to 100 bar by a step of 10 bar. For each boiler pressure and constant output power, firstly, the fuel mass flow rate, steam flow rate, energy and exergy efficiency, and cost of electricity were calculated. Secondly, entropy generation, exergy destruction, and exergy efficiency for each component were calculated. Finally, exergy destruction economics for each component of the plant was performed. The results reveal that increasing the boiler pressure from (10 to 100 bar) for constant output power reduces the cost of electricity from (0.135 to 0.1025 $/kWh) due to a decrease in the fuel mass flow rate and an improvement in the thermal cycle and exergy efficiency. Also, when the boiler pressure increases, the exergy destruction for the pump increases, the exergy destruction for the boiler decreases, the exergy destruction for the turbine increases, and the exergy destruction for the condenser decrease.
In this work, both energy and exergy analyses have been carried out on General Electric (GE) gas turbine unit found in Khor Al-Zubair gas turbine power plant located in Basra, Iraq. The analysis covers the ISO (international standards organization) operating conditions in addition to actual operating data recorded for one month in hot season July 2016. The feasibility of adopting a vapor compression cycle (VCC) for cooling the intake air is evaluated. Generally, the study reveals an obvious drop off for most plant performance characteristics while operating during the hot season. Energy and exergy analyses show that adopting the vapor compression cycle to enhance Khor Al-Zubair GE unit could improve the power output by 20% and 27% in case of part-load and full-load conditions respectively. Both of first and second law efficiencies could be improved by 3.5% at part- load and 9% at full load. The expected cooling load needed for the unit is in the range of 2697 to 3024.5 TR according to part- load and full-load operation respectively. Only total irreversibility of the unit is expected to increase in case of adopting VCC and this will not impair the improvement in second law efficiency of the unit. Among the unit components, combustion chamber has the largest computed irreversibility. Further improvement is recommended by utilizing the released heat energy to the atmosphere, which is characterized by significant work potential.