×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerVan Kármán vortex street is considered an important phenomenon that accompanies fluid flow, especially when exposed to a certain barrier, as periodic vortexes occur on both sides of the body that rotate in two opposite directions. This phenomenon occurs in the atmosphere around mountains, oceans, seas, and islands. Also, this phenomenon makes it possible to induce a fluid flow around a specific body present in the flow path. In this study, a model for fluid flow around a cylinder of a certain diameter was taken, where the flow near the boundary layers of the cylinder surface moves slower than near the free stream. In addition, the pressure distribution was studied, and it was observed that there is a pressure gradient due to the difference in momentum at the surface of the cylinder in distant areas due to friction. The study area was divided into fine meshes with Fluent software, especially in the irregular areas. The simulation was implemented for Reynolds numbers Re = 100 and Re = 1500 for incompressible flows. Consequently, the equations that do not depend on pressure are difficult to solve. Therefore, methods linking pressure and velocity were adopted, where the pressure-velocity coupling simple method was used. The first-order forward difference scheme was adopted in representing the differential equations as a function of time when performing the simulation. From the steady state and upwards to Reynolds number Re = 100, it was observed that a twain of vortices appeared on the body at a certain speed range. When the state was changed from the stable state to the transitional state, the results changed, as the flow became asymmetric and unsteady due to vortex shedding phenomena, which led to the generation of vortexes in different ways. The U-Velocity curve was studied for two different cases, and the results showed a large discrepancy between the first order and the second order, where the second order had better behavior but required great effort to reach accurate results. Also, pressure-velocity was studied to satisfy mass conservation, and numerical techniques were used to c ompute the equations of Navier-Stokes in CFD, such as SIMPLEC, PISO, and SIMPLE. An acceptable convergence was not reached with the PISO; therefore, the SIMPLE method was adopted. The pressure gradient was drawn around the cylinder, where it was observed that the pressure was greatest at the front of the cylinder and its lowest value at the end.
The dieless drawing process is an innovative method emanated and appeared in coincidence with development of the concept of metal superplasticity. It is utilized from the local heating of a wire or tube to a specified temperature and followed by a local cooling, so an additional deformation is inhibited. In this study, a special dieless drawing machine was designed to carry out an experimental program on SUS304-stainless steel wire having diameter of (1.6-2) mm to investigate the main process parameters such as speeds, heat quantity, heating coil width and heating-cooling separation distance. Also, a numerical model based on thermo-mechanical analysis was developed and validated with experimental program. Furthermore, an artificial neural network ANN model based on current experimental data was prepared to predict the dieless drawing behavior. A maximum area reduction of 40.7% was obtained in single pass. A 3.12mm/s feeding velocity and 4.97mm/s drawing velocity were realized through the experimental tests. The results showed that both drawing force and wire profile were effected by increasing of feeding speed, heating coil width and separation distance. Also, it is confirmed that strain rate was reduced by increasing the heating coil width and the reduction ratio was promoted. A maximum error of 21% was recorded between ANN model and experimental results. The results showed a good agreement among experimental, numerical and ANN models.
The solar chimney power plant is one of the modern models studied on the world. This study presents an engineering and numerical analysis of solar chimney with different parameters. Also, it studies the comparison of two collector base shapes(circular and hexagonal) depend on the five storage material types and their effects on the heat transfer, velocity, efficiency, etc. inside the solar chimney system by considering the solar array intensity equations and the energy equation to calculate the heat transferred and stored by applying the laws of CFD. The finite volume method is used to analyze the geometry physical model by applying a commercial Fluent 6.3 code with Gambit 2.3. The obtained results show that the efficiency of solar chimney is increased by increasing the area of solar glassed collector with circular base shape than the others of polygonal or rectangular one because the circular was covered large area of system. So, the circular ground collector shape for thermal storage is the favour because it is the better to increase the velocity of entering air and to increase the efficiency of turbine. In addition to that the black Pebble storage plate is the better material for heat storage which is convected to air passed for operation of turbine than the other types aluminum, tar, copper and steel seriously.
Type of metal flow and stress distribution in metal extrusion process is a highly complex for the complicated die design. In this work a finite element simulation of Al-1100 rod extrusion was successfully achieved using the commercial finite element code Deform-3D.The results show that the finite element model was successfully simulate the stress distribution in the direct rod extrusion of Al-1100.Besides that the optimum die angle reduces the magnitude of normal, shear, and effective stresses. We can conclude from this studythat maximum stresses occour when the rod is with contact with the die at exit stage.