×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerIn this paper, the Weibull uni-axial and multi-axial distribution function for polyethylene pips under pressure loading were developed and analyzed taking account of residual stress. Tensile test was achieved to determine mechanical properties and the Weibull parameters. Experimental method using the hole- drilling strain-gage method was used to measure the residual stresses in PE pipe and compare with that obtained from numerical finite element method (FEM). The obtained results show that there is a convergence between uni-axial and multi-axial distribution function, but multi-axial distribution function give large values compared to uni-axial distribution function. It was observed that the residual stresses have influence on failure assessment diagram and causes translation from elastic-plastic failure to brittle failure.
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, Weibull uni-axial and multi-axial distribution function is applied to evaluate the reliability of the fracture strength of rotating turbine rotor wheel manufactured from ceramic material and have inner surface crack. Three cases are considered, first taking only the effect of rotational stresses, second taking the effect of rotational and thermal stresses in ceramic disc, and third taking the effect of rotational and thermal loading in ceramic blade. It was found that there is a convergence between results gotten from uni-axial and multi-axial distribution function, but multi-axial distribution function give small large in values result compared to uni-axial distribution function. The expected values of rupture strength of ceramic blade is higher than of that of disc material, therefore the failure occurs in blade first than in disc material in service survival.
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
This paper studies and compared the fatigue crack propagation rate da/dN for three kinds of ceramic wheel (model A, model B, and model C) made of Si3N4 ceramic with different additives used for gas turbine application. The stress intensity factor range was calculated using finite element method and then compared with analytical approximate approaches. Experimental fatigue test was carried out on the three specimens taken from the models. As a result, the types of additives effect on fatigue crack propagation rate. The model A has the highest da/dN values and model C exhibits the lower values of da/dN.
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, depends on the finite element method, the J-Integral program is developed for a stationary circumferential crack problem in elastic plastic fracture mechanics in pipes under static loading and pure bending moment condition. The program developed is applied to ductile cast iron pipes (DCIP) to analys the integrity assessment, i.e., the significance of crack growth by drawing both failure assessment diagram (FAD) and crack driving force diagram (CDF). A numerical procedure is used for elastic-plastic analysis depending on special equation to predict J-values taking account of the crack geometry and load condition. It is cleared that the results obtained from failure assessment diagram and crack driving force diagram are identical and J-integral method can be used to the onset of crack growth in (DCIP) under bending moment conditions.
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec
In this paper, a finite element method program under domain loading and plain strain conditions is developed and applied in evaluation of the stress intensity factor in opening mode (K1) in two dimensions crack problems. Two types of crack problems analyzed and verified: first, cracked rotating disc made from bi-directional fiber reinforced material composite, second crack blade made from bi-directional fiber reinforced metal matrix composite. It is found that the finite element method under domain loading is a good tool for the analysis of composite material. The simulation is accurate in comparison with that obtained from extrapolation method. The stress intensity factor for fiber reinforced metal matrix composite is larger when obtained from fiber-reinforced material under same condition.
In this paper, the influence of thermal residual stress on strength and fracture rotating speed of composite disc is studied and analyzed using finite difference method and laminated plate theory for two types of reinforced composite discs (radial fiber reinforced disc and circumferential fiber reinforced disc). As a result the thermal residual stress will reduce radial and tangential stresses in radial fiber reinforced disc, while it shall increase radial stresses and decrease tangential stresses in circumferential fiber reinforced disc. The existing of residual stresses in composite disc will leads to initiation of crack and begins to propagation near the inner diameter compared to case when neglecting residual stress for cases taken in analysis. It is also verified that the finite difference method is a good tool for stress analysis of composite disc under residual stress effec