×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThis paper presents a pressure drop analysis in perforated vertical wellbores for different perforation parameters. The effect of the density of the perforations (number of perforation), the phase angle of the perforations, the diameter of the perforation and the flow rate of the crude oil from the perforations on the pressure drop and the productivity index of the perforated vertical wellbores were studied. The analysis of the vertical wellbore was performed numerically using ANSYS FLUENT 15.0 software. Three dimensional, steady-states, turbulent and incompressible fluid flow is assumed during the numerical solution of the governing equations. The results of this study show that, increased perforation density of the perforated vertical wellbore caused an increase in pressure drop, and also, decreased productivity index due to increasing the friction losses. Friction pressure drop has a significant effect on crude oil flow into the wellbore. When the main velocity is 1.5 m/s and the inlet velocity from the perforations is 2 m/s, the friction pressure drop is about 66 % and the acceleration pressure is approximately 34 % of the total pressure drop.
In recent decades, the need for strengthening and repairing reinforced concrete structures has increasingly arisen. One common method is the use of concrete jackets. Slurry Infiltrated Fiber Concrete (SIFCON), a newly developed material, offers superior mechanical properties, making it a preferred choice for strengthening and repairing concrete structures. However, there is limited understanding of its bonding performance when used as an overlay on a Normal Strength Concrete (NSC) substrate. This study conducted a direct Shear Test (DST) to evaluate the bond performance using reinforced NSC cubes externally bonded with SIFCON jackets subjected to direct shear. Eighteen reinforced cubes were strengthened with various bonding systems to investigate how different factors affect the bond performance between the NSC substrate and SIFCON overlay. The parameters studied included surface preparation methods, binder types, jacket configurations, bonding conditions (fresh overlay on hardened substrate and hardened overlay on hardened substrate), dowel placement, and bonding mechanisms. The results show that using bonding agents significantly improved bond strength, with epoxy proving more effective than latex. Specimens prepared by chipping showed better bonding performance compared to those prepared through diamond cutting. Chipping increased bond strength by 8.91% to 13.84% over diamond cutting in the case of fresh SIFCON overlay on hardened substrate. Using dowels in the bonding systems also improved bond performance by 10.89% to 16.97%. Applying jackets to three sides instead of two increased the ultimate failure load by 31.76% when dowels were used in both the two-sided and three-sided strengthened samples, and by 35.45% in the absence of dowels in both types of strengthened specimens. The cast-in-situ specimens demonstrated superiority over those strengthened with precast jacket layers.
A numerical simulation of the effect evaluation of heat loss and temperature distribution along the wellbore is performed, for two models, the first is an open hole (without perforation) and the other is a perforated vertical wellbore. In this study, the Computational Fluid Dynamics (CFD) software code ANSYS FLUENT 15.0 has been used, for simulate a model of 3-D turbulent flow with stander k-ϵ model. The results of this show that, increasing the heat losses leads to an increase in the temperature gradient, while the temperature gradient decreases with increasing inlet main velocity. Also, the temperature of the produced crude oil decreases with increasing the length of the wellbore.
In this paper, a compact ultra-wide band (UWB) printed patch antenna is designed and optimized using four biologically and plant inspired optimization algorithms. These algorithms are the newly adopted Moss Rose Optimization Algorithm (MROA), Runner Root Algorithm (RRA), Sunflower Optimization Algorithm (SFOA) and Particle Swarm Optimization (PSO). These algorithms are modified in an optimizer software, which merges the attributes of the design of electromagnetic environment of CST Microwave Studio with those of the technical programming environment of MATLAB. A compact (12 × 21.5) mm 2 printed patch antenna has been proposed and simulated over the whole UWB frequency range using these four optimization algorithms. The simulation results show the superiority of the antenna design using MROA, which has the widest covered frequency range, the lowest reflection coefficient and the lowest standing wave ratio.